[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C235;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22DH;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=300;ssr=SSR10DA;lot=20260616;uid=61C229 [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=4E0060000F51353135323934

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.3991 gap=1.6009 (chauffe, ignore) tap 2: pos=255.9969 gap=2.0031 (1/4) tap 3: pos=255.9969 gap=2.0031 (2/4) tap 4: pos=255.9969 gap=2.0031 (3/4) tap 5: pos=255.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=255.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=256.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.5819 gap=1.4181 (chauffe, ignore) tap 2: pos=-29.9847 gap=2.0153 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0122/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9938 spread=0.0122mm (tol=0.0500). Zero pose en butee=-30.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=255.9969 gap=2.0031 (1/4) tap 3: pos=255.9969 gap=2.0031 (2/4) tap 4: pos=255.9969 gap=2.0031 (3/4) tap 5: pos=255.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=255.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=256.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.9597 gap=1.0403 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=255.9969 gap=2.0031 (1/4) tap 3: pos=255.9969 gap=2.0031 (2/4) tap 4: pos=255.9969 gap=2.0031 (3/4) tap 5: pos=255.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=255.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=256.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.9597 gap=1.0403 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Moving to tap point X=31.0 Y=212.0... Probing with pressure switch... probe at 31.003,211.998 is z=265.575000 probe at 31.003,211.998 is z=207.862500 Tap drift (diff=57.7125mm) — reset probe at 31.003,211.998 is z=176.492500 Tap drift (diff=31.3700mm) — reset probe at 31.003,211.998 is z=176.490000 Tap OK (diff=0.0025mm, stable 2/5) probe at 31.003,211.998 is z=176.470000 Tap drift (diff=0.0200mm) — reset probe at 31.003,211.998 is z=176.460000 Tap drift (diff=0.0100mm) — reset Tap OK (diff=0.0000mm, stable 2/5) probe at 31.003,211.998 is z=176.455000 Tap OK (diff=0.0050mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) probe at 31.003,211.998 is z=176.452500 Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=176.4525 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (31.0, 212.0) ~ point de tap (31.0, 212.0) Z calibration complete!

Moving to tap point X=31.0 Y=212.0... Probing with pressure switch... probe at 30.994,211.998 is z=0.877500 probe at 30.994,211.998 is z=3.420000 Tap drift (diff=2.5425mm) — reset probe at 30.994,211.998 is z=5.952500 Tap drift (diff=2.5325mm) — reset probe at 30.994,211.998 is z=8.102500 Tap drift (diff=2.1500mm) — reset probe at 30.994,211.998 is z=0.880000 Tap drift (diff=7.2225mm) — reset probe at 30.994,211.998 is z=3.425000 Tap drift (diff=2.5450mm) — reset probe at 30.994,211.998 is z=5.955000 Tap drift (diff=2.5300mm) — reset probe at 30.994,211.998 is z=8.490000 Tap drift (diff=2.5350mm) — reset probe at 30.994,211.998 is z=11.022500 probe at 30.994,211.998 is z=13.557500 probe at 30.994,211.998 is z=1.530000 Tap drift (diff=12.0275mm) — reset probe at 30.994,211.998 is z=0.947500 Tap drift (diff=0.5825mm) — reset probe at 30.994,211.998 is z=0.937500 Tap OK (diff=0.0100mm, stable 2/5) probe at 30.994,211.998 is z=0.862500 Tap drift (diff=0.0750mm) — reset probe at 30.994,211.998 is z=0.860000 Tap OK (diff=0.0025mm, stable 2/5) probe at 30.994,211.998 is z=0.857500 Tap OK (diff=0.0025mm, stable 3/5) probe at 30.994,211.998 is z=0.852500 Tap OK (diff=0.0050mm, stable 4/5) probe at 30.994,211.998 is z=0.825000 Tap drift (diff=0.0275mm) — reset Tap OK (diff=0.0000mm, stable 2/5) probe at 30.994,211.998 is z=0.827500 Tap OK (diff=0.0025mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=0.8250 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000)

probe: at 32.495,205.497 bed will contact at z=1.282500 probe: at 32.495,205.497 bed will contact at z=1.312500 probe: at 32.495,205.497 bed will contact at z=1.315000 probe: at 206.996,205.497 bed will contact at z=2.630000 probe: at 206.996,205.497 bed will contact at z=2.642500 probe: at 206.996,205.497 bed will contact at z=2.655000 probe: at 206.996,31.995 bed will contact at z=4.327500 probe: at 206.996,31.995 bed will contact at z=4.350000 probe: at 206.996,31.995 bed will contact at z=4.355000 probe: at 32.495,31.995 bed will contact at z=3.460000 probe: at 32.495,31.995 bed will contact at z=3.475000 probe: at 32.495,31.995 bed will contact at z=3.445000 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=49.5, y=175.5, z=1.31250 front right screw : x=224.0, y=175.5, z=2.64250 : adjust CW 02:40 rear right screw : x=224.0, y=2.0, z=4.35000 : adjust CW 06:05 rear left screw : x=49.5, y=2.0, z=3.46000 : adjust CW 04:18