[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C435;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22S148H;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=750;ssr=SSR10DA;lot=20260618;uid=9221AF [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=500044000F51353135323934

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=467.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=466.9969 gap=2.0031 (1/4) tap 3: pos=466.9969 gap=2.0031 (2/4) tap 4: pos=466.9969 gap=2.0031 (3/4) tap 5: pos=466.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=466.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=467.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-20.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-20.9969 gap=2.0031 (1/4) tap 3: pos=-20.9969 gap=2.0031 (2/4) tap 4: pos=-20.9969 gap=2.0031 (3/4) tap 5: pos=-20.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-20.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-21.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=467.5697 gap=1.4303 (chauffe, ignore) tap 2: pos=466.9969 gap=2.0031 (1/4) tap 3: pos=466.9969 gap=2.0031 (2/4) tap 4: pos=467.1797 gap=1.8203 (3/4) tap 5: pos=466.9969 gap=2.0031 fenetre=0.1828/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=467.0426 spread=0.1828mm (tol=0.0500). Zero pose en butee=467.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-20.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-20.9969 gap=2.0031 (1/4) tap 3: pos=-20.9969 gap=2.0031 (2/4) tap 4: pos=-20.9969 gap=2.0031 (3/4) tap 5: pos=-20.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-20.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-21.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 125mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=467.5697 gap=1.4303 (chauffe, ignore) tap 2: pos=466.9969 gap=2.0031 (1/4) tap 3: pos=466.9969 gap=2.0031 (2/4) tap 4: pos=466.9969 gap=2.0031 (3/4) tap 5: pos=467.1797 gap=1.8203 fenetre=0.1828/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=467.0426 spread=0.1828mm (tol=0.0500). Zero pose en butee=467.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-20.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-20.9969 gap=2.0031 (1/4) tap 3: pos=-20.9969 gap=2.0031 (2/4) tap 4: pos=-20.9969 gap=2.0031 (3/4) tap 5: pos=-20.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-20.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-21.0000 Moving to tap point X=56.0 Y=334.0... Probing with pressure switch... probe at 55.998,334.001 is z=473.780000 probe at 55.998,334.001 is z=405.865000 Tap drift (diff=67.9150mm) — reset Tap OK (diff=0.0000mm, stable 2/5) probe at 55.998,334.001 is z=405.860000 Tap OK (diff=0.0050mm, stable 3/5) probe at 55.998,334.001 is z=405.867500 Tap OK (diff=0.0075mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=405.8675 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (56.0, 334.0) ~ point de tap (56.0, 334.0) Z calibration complete!

Moving to tap point X=56.0 Y=334.0... Probing with pressure switch... probe at 56.001,334.001 is z=389.322500 probe at 56.001,334.001 is z=390.990000 Tap drift (diff=1.6675mm) — reset probe at 56.001,334.001 is z=393.682500 Tap drift (diff=2.6925mm) — reset probe at 56.001,334.001 is z=396.317500 Tap drift (diff=2.6350mm) — reset probe at 56.001,334.001 is z=399.035000 Tap drift (diff=2.7175mm) — reset Switch encore declenche (vibration) -> attente 2.0s puis nouvelle tentative (1/10) probe at 56.001,334.001 is z=278.462500 Tap drift (diff=120.5725mm) — reset probe at 56.001,334.001 is z=281.110000 Tap drift (diff=2.6475mm) — reset probe at 56.001,334.001 is z=229.442500 Tap drift (diff=51.6675mm) — reset probe at 56.001,334.001 is z=232.142500 Tap drift (diff=2.7000mm) — reset probe at 56.001,334.001 is z=196.645000 Tap drift (diff=35.4975mm) — reset probe at 56.001,334.001 is z=149.422500 Tap drift (diff=47.2225mm) — reset probe at 56.001,334.001 is z=152.135000 Tap drift (diff=2.7125mm) — reset probe at 56.001,334.001 is z=149.990000 Tap drift (diff=2.1450mm) — reset probe at 56.001,334.001 is z=23.652500 Tap drift (diff=126.3375mm) — reset probe at 56.001,334.001 is z=23.667500 Tap drift (diff=0.0150mm) — reset probe at 56.001,334.001 is z=23.672500 Tap OK (diff=0.0050mm, stable 2/5) probe at 56.001,334.001 is z=23.670000 Tap OK (diff=0.0025mm, stable 3/5) Tap OK (diff=0.0025mm, stable 4/5) probe at 56.001,334.001 is z=23.690000 Tap drift (diff=0.0175mm) — reset probe at 56.001,334.001 is z=23.685000

probe: at 56.003,334.994 bed will contact at z=2.552500 probe: at 56.003,334.994 bed will contact at z=2.535000 probe: at 56.003,334.994 bed will contact at z=2.540000 probe: at 388.002,334.994 bed will contact at z=2.512500 probe: at 388.002,334.994 bed will contact at z=2.507500 probe: at 388.002,110.001 bed will contact at z=2.470000 probe: at 388.002,110.001 bed will contact at z=2.462500 probe: at 56.003,110.001 bed will contact at z=2.487500 probe: at 56.003,110.001 bed will contact at z=2.485000 probe: at 56.003,110.001 bed will contact at z=2.490000 probe: at 221.996,222.004 bed will contact at z=2.510000 probe: at 221.996,222.004 bed will contact at z=2.495000 probe: at 221.996,222.004 bed will contact at z=2.522500 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=73.0, y=305.0, z=2.54000 front right screw : x=405.0, y=305.0, z=2.51250 : adjust CCW 00:03 rear right screw : x=405.0, y=80.0, z=2.47000 : adjust CCW 00:08 rear left screw : x=73.0, y=80.0, z=2.48750 : adjust CCW 00:06 rear middle screw : x=239.0, y=192.0, z=2.51000 : adjust CCW 00:04