[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C435;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22S148H;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=750;ssr=SSR10DA;lot=20260618;uid=9221AF [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=50004C000F51353135323934

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=467.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=466.9969 gap=2.0031 (1/4) tap 3: pos=466.9969 gap=2.0031 (2/4) tap 4: pos=466.9969 gap=2.0031 (3/4) tap 5: pos=466.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=466.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=467.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-21.0091 gap=1.9909 (chauffe, ignore) tap 2: pos=-20.9969 gap=2.0031 (1/4) tap 3: pos=-20.9969 gap=2.0031 (2/4) tap 4: pos=-20.9969 gap=2.0031 (3/4) tap 5: pos=-20.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-20.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-21.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=467.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=466.9969 gap=2.0031 (1/4) tap 3: pos=466.9969 gap=2.0031 (2/4) tap 4: pos=466.9969 gap=2.0031 (3/4) tap 5: pos=466.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=466.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=467.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-20.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-20.9969 gap=2.0031 (1/4) tap 3: pos=-20.9969 gap=2.0031 (2/4) tap 4: pos=-20.9969 gap=2.0031 (3/4) tap 5: pos=-20.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-20.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-21.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=467.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=466.9969 gap=2.0031 (1/4) tap 3: pos=466.9969 gap=2.0031 (2/4) tap 4: pos=466.9969 gap=2.0031 (3/4) tap 5: pos=466.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=466.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=467.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-20.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-20.9969 gap=2.0031 (1/4) tap 3: pos=-20.9969 gap=2.0031 (2/4) tap 4: pos=-20.9969 gap=2.0031 (3/4) tap 5: pos=-20.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-20.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-21.0000 Moving to tap point X=56.0 Y=334.0... Probing with pressure switch... probe at 55.998,334.001 is z=405.500000 Tap OK (diff=0.0000mm, stable 2/5) probe at 55.998,334.001 is z=405.612500 Tap drift (diff=0.1125mm) — reset probe at 55.998,334.001 is z=405.655000 Tap drift (diff=0.0425mm) — reset probe at 55.998,334.001 is z=405.540000 Tap drift (diff=0.1150mm) — reset probe at 55.998,334.001 is z=405.542500 Tap OK (diff=0.0025mm, stable 2/5) Tap drift (diff=0.1550mm) — reset probe at 55.998,334.001 is z=405.652500 Tap drift (diff=0.0400mm) — reset probe at 55.998,334.001 is z=405.495000 Tap drift (diff=0.1575mm) — reset probe at 55.998,334.001 is z=405.575000 Tap drift (diff=0.0800mm) — reset probe at 55.998,334.001 is z=405.532500 Tap drift (diff=0.1200mm) — reset probe at 55.998,334.001 is z=405.617500 Tap drift (diff=0.0350mm) — reset

Moving to tap point X=56.0 Y=334.0... Probing with pressure switch... probe at 56.001,334.001 is z=449.087500 probe at 56.001,334.001 is z=329.810000 Tap drift (diff=119.2775mm) — reset probe at 56.001,334.001 is z=1.065000 Tap drift (diff=328.7450mm) — reset probe at 56.001,334.001 is z=1.092500 Tap drift (diff=0.0275mm) — reset probe at 56.001,334.001 is z=1.095000 Tap OK (diff=0.0025mm, stable 2/5) probe at 56.001,334.001 is z=1.097500 Tap OK (diff=0.0025mm, stable 3/5) probe at 56.001,334.001 is z=1.090000 Tap OK (diff=0.0075mm, stable 4/5) Tap OK (diff=0.0075mm, stable 5/5) VALIDATED: trigger_z=1.0975 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (56.0, 334.0) ~ point de tap (56.0, 334.0) Z calibration complete! probe at 56.001,334.001 is z=486.087500 probe at 56.001,334.001 is z=486.102500 Tap drift (diff=0.0150mm) — reset probe at 56.001,334.001 is z=486.100000 probe at 56.001,334.001 is z=486.097500 Tap OK (diff=0.0025mm, stable 4/5) Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=486.0975 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=486.1000 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Tap OK (diff=0.0050mm, stable 2/5) probe at 56.001,334.001 is z=486.105000 probe at 56.001,334.001 is z=486.095000 VALIDATED: trigger_z=486.0950 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Tap OK (diff=0.0000mm, stable 2/5) probe at 56.001,334.001 is z=486.110000 Tap OK (diff=0.0075mm, stable 3/5) probe at 56.001,334.001 is z=486.107500 VALIDATED: trigger_z=486.1075 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) probe at 56.001,334.001 is z=486.092500 Tap OK (diff=0.0000mm, stable 3/5)

probe: at 56.003,334.994 bed will contact at z=1.697500 probe: at 56.003,334.994 bed will contact at z=1.700000 probe: at 388.002,334.994 bed will contact at z=1.642500 probe: at 388.002,334.994 bed will contact at z=1.632500 probe: at 388.002,110.001 bed will contact at z=1.630000 probe: at 388.002,110.001 bed will contact at z=1.620000 probe: at 56.003,110.001 bed will contact at z=1.692500 probe: at 56.003,110.001 bed will contact at z=1.715000 probe: at 56.003,110.001 bed will contact at z=1.717500 probe: at 221.996,222.004 bed will contact at z=1.700000 probe: at 221.996,222.004 bed will contact at z=1.707500 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=73.0, y=305.0, z=1.69750 front right screw : x=405.0, y=305.0, z=1.64250 : adjust CCW 00:07 rear right screw : x=405.0, y=80.0, z=1.63000 : adjust CCW 00:08 rear left screw : x=73.0, y=80.0, z=1.71500 : adjust CW 00:02 rear middle screw : x=239.0, y=192.0, z=1.70750 : adjust CW 00:01