[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C435;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22S148H;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=750;ssr=SSR10DA;lot=20260618;uid=9221AF [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=500053000F51353135323934

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.2163 gap=1.7837 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.9597 gap=1.0403 (chauffe, ignore) tap 2: pos=-18.7769 gap=1.2231 (1/4) tap 3: pos=-18.7769 gap=1.2231 (2/4) tap 4: pos=-18.7769 gap=1.2231 (3/4) tap 5: pos=-18.5941 gap=1.4059 fenetre=0.1828/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-18.7312 spread=0.1828mm (tol=0.0500). Zero pose en butee=-18.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.5697 gap=1.4303 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.9597 gap=1.0403 (chauffe, ignore) tap 2: pos=-18.5941 gap=1.4059 (1/4) tap 3: pos=-18.1797 gap=1.8203 (2/4) tap 4: pos=-18.7769 gap=1.2231 (3/4) tap 5: pos=-18.7769 gap=1.2231 fenetre=0.5972/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-18.5819 spread=0.5972mm (tol=0.0500). Zero pose en butee=-18.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.5697 gap=1.4303 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.7769 gap=1.2231 (chauffe, ignore) tap 2: pos=-18.1797 gap=1.8203 (1/4) tap 3: pos=-18.7769 gap=1.2231 (2/4) tap 4: pos=-18.7769 gap=1.2231 (3/4) tap 5: pos=-18.7769 gap=1.2231 fenetre=0.5972/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-18.6276 spread=0.5972mm (tol=0.0500). Zero pose en butee=-18.0000 Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.995,339.999 is z=407.437500 probe at 49.995,339.999 is z=407.432500 Tap OK (diff=0.0050mm, stable 2/5) probe at 49.995,339.999 is z=407.435000 Tap OK (diff=0.0025mm, stable 3/5) probe at 49.995,339.999 is z=407.440000 Tap OK (diff=0.0050mm, stable 4/5) Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=407.4375 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (50.0, 340.0) ~ point de tap (50.0, 340.0) Z calibration complete!

Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.998,339.999 is z=480.640000 probe at 49.998,339.999 is z=483.122500 Tap drift (diff=2.4825mm) — reset probe at 49.998,339.999 is z=482.237500 Tap drift (diff=0.8850mm) — reset probe at 49.998,339.999 is z=437.865000 Tap drift (diff=44.3725mm) — reset probe at 49.998,339.999 is z=215.235000 Tap drift (diff=222.6300mm) — reset probe at 49.998,339.999 is z=204.890000 Tap drift (diff=10.3450mm) — reset probe at 49.998,339.999 is z=180.587500 Tap drift (diff=24.3025mm) — reset probe at 49.998,339.999 is z=173.442500 Tap drift (diff=7.1450mm) — reset probe at 49.998,339.999 is z=176.200000 Tap drift (diff=2.7575mm) — reset probe at 49.998,339.999 is z=175.032500 Tap drift (diff=1.1675mm) — reset probe at 49.998,339.999 is z=177.797500 Tap drift (diff=2.7650mm) — reset probe at 49.998,339.999 is z=136.352500 Tap drift (diff=41.4450mm) — reset probe at 49.998,339.999 is z=50.387500 Tap drift (diff=85.9650mm) — reset probe at 49.998,339.999 is z=1.090000 Tap drift (diff=49.2975mm) — reset probe at 49.998,339.999 is z=1.087500 Tap OK (diff=0.0025mm, stable 2/5) Tap OK (diff=0.0025mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) probe at 49.998,339.999 is z=1.092500 Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=1.0925 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (50.0, 340.0) ~ point de tap (50.0, 340.0) Z calibration complete! probe at 49.998,339.999 is z=486.100000 probe at 49.998,339.999 is z=486.097500

probe: at 54.997,328.001 bed will contact at z=1.225000 probe: at 54.997,328.001 bed will contact at z=1.220000 probe: at 54.997,328.001 bed will contact at z=1.215000 probe: at 380.001,328.001 bed will contact at z=1.160000 probe: at 380.001,328.001 bed will contact at z=1.165000 probe: at 380.001,328.001 bed will contact at z=1.155000 probe: at 380.001,101.996 bed will contact at z=1.240000 probe: at 380.001,101.996 bed will contact at z=1.217500 probe: at 380.001,101.996 bed will contact at z=1.245000 probe: at 54.997,101.996 bed will contact at z=1.267500 probe: at 54.997,101.996 bed will contact at z=1.262500 probe: at 54.997,101.996 bed will contact at z=1.260000 probe: at 217.505,214.498 bed will contact at z=1.205000 probe: at 217.505,214.498 bed will contact at z=1.210000 probe: at 217.505,214.498 bed will contact at z=1.207500 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=72.0, y=298.0, z=1.22000 front right screw : x=397.0, y=298.0, z=1.16000 : adjust CCW 00:07 rear right screw : x=397.0, y=72.0, z=1.24000 : adjust CW 00:02 rear left screw : x=72.0, y=72.0, z=1.26250 : adjust CW 00:05 middle : x=234.5, y=184.5, z=1.20750 : adjust CCW 00:01