[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C435;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22S148H;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=110V;bedw=550;ssr=SSR10DA;lot=20260618;uid=2ACAAE [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=520065001051353135323934

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.7525 gap=1.2475 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=457.0091 gap=1.9909 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9847 gap=2.0153 fenetre=0.0244/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0244mm (tol=0.0500). Zero pose en butee=457.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.3747 gap=1.6253 (chauffe, ignore) tap 2: pos=-18.7769 gap=1.2231 (1/4) tap 3: pos=-18.5941 gap=1.4059 (2/4) tap 4: pos=-18.9597 gap=1.0403 (3/4) tap 5: pos=-18.3991 gap=1.6009 fenetre=0.5606/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-18.6824 spread=0.5606mm (tol=0.0500). Zero pose en butee=-18.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.5575 gap=1.4425 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-17.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-17.9969 gap=2.0031 (1/4) tap 3: pos=-17.9969 gap=2.0031 (2/4) tap 4: pos=-18.3747 gap=1.6253 (3/4) tap 5: pos=-18.3991 gap=1.6009 fenetre=0.4022/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-18.1919 spread=0.4022mm (tol=0.0500). Zero pose en butee=-18.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 125mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.5697 gap=1.4303 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-17.9847 gap=2.0153 (chauffe, ignore) tap 2: pos=-17.9969 gap=2.0031 (1/4) tap 3: pos=-17.9969 gap=2.0031 (2/4) tap 4: pos=-17.9969 gap=2.0031 (3/4) tap 5: pos=-17.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-17.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-18.0000 Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.995,339.999 is z=385.915000 probe at 49.995,339.999 is z=385.940000 Tap drift (diff=0.0250mm) — reset Tap OK (diff=0.0000mm, stable 2/5) probe at 49.995,339.999 is z=385.942500 Tap OK (diff=0.0025mm, stable 3/5) probe at 49.995,339.999 is z=385.947500 Tap OK (diff=0.0050mm, stable 4/5) Tap OK (diff=0.0050mm, stable 5/5) VALIDATED: trigger_z=385.9425 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (50.0, 340.0) ~ point de tap (50.0, 340.0) Z calibration complete!

Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.998,339.999 is z=479.467500 probe at 49.998,339.999 is z=466.952500 Tap drift (diff=12.5150mm) — reset probe at 49.998,339.999 is z=460.025000 Tap drift (diff=6.9275mm) — reset probe at 49.998,339.999 is z=452.042500 Tap drift (diff=7.9825mm) — reset probe at 49.998,339.999 is z=444.040000 Tap drift (diff=8.0025mm) — reset probe at 49.998,339.999 is z=436.412500 Tap drift (diff=7.6275mm) — reset probe at 49.998,339.999 is z=434.077500 Tap drift (diff=2.3350mm) — reset probe at 49.998,339.999 is z=394.375000 Tap drift (diff=39.7025mm) — reset probe at 49.998,339.999 is z=0.897500 Tap drift (diff=393.4775mm) — reset probe at 49.998,339.999 is z=0.907500 Tap drift (diff=0.0100mm) — reset Tap OK (diff=0.0000mm, stable 2/5) probe at 49.998,339.999 is z=0.910000 Tap OK (diff=0.0025mm, stable 3/5) Tap OK (diff=0.0025mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=0.9075 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (50.0, 340.0) ~ point de tap (50.0, 340.0) Z calibration complete! probe at 49.998,339.999 is z=485.902500 probe at 49.998,339.999 is z=485.905000 Tap OK (diff=0.0000mm, stable 4/5) VALIDATED: trigger_z=485.9050 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) probe at 49.998,339.999 is z=485.897500 probe at 49.998,339.999 is z=485.900000 Tap OK (diff=0.0025mm, stable 2/5) Tap OK (diff=0.0000mm, stable 3/5) Tap OK (diff=0.0025mm, stable 5/5) probe at 49.998,339.999 is z=485.895000 VALIDATED: trigger_z=485.8975 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000)

probe: at 54.997,328.001 bed will contact at z=2.322500 probe: at 54.997,328.001 bed will contact at z=2.330000 probe: at 380.001,328.001 bed will contact at z=2.342500 probe: at 380.001,328.001 bed will contact at z=2.355000 probe: at 380.001,328.001 bed will contact at z=2.350000 probe: at 380.001,101.996 bed will contact at z=2.322500 probe: at 380.001,101.996 bed will contact at z=2.317500 probe: at 380.001,101.996 bed will contact at z=2.332500 probe: at 54.997,101.996 bed will contact at z=2.365000 probe: at 54.997,101.996 bed will contact at z=2.362500 probe: at 217.505,214.498 bed will contact at z=2.407500 probe: at 217.505,214.498 bed will contact at z=2.400000 probe: at 217.505,214.498 bed will contact at z=2.402500 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=72.0, y=298.0, z=2.33000 front right screw : x=397.0, y=298.0, z=2.35000 : adjust CW 00:02 rear right screw : x=397.0, y=72.0, z=2.32250 : adjust CCW 00:01 rear left screw : x=72.0, y=72.0, z=2.36500 : adjust CW 00:04 middle : x=234.5, y=184.5, z=2.40250 : adjust CW 00:09