[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C335;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22DH;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=500;ssr=SSR10DA;lot=20260618;uid=36C6E9 [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=54002E001051353135323934

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-29.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-29.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-29.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.996,275.995 is z=383.410000 probe at 65.996,275.995 is z=369.455000 Tap drift (diff=13.9550mm) — reset probe at 65.996,275.995 is z=364.700000 Tap drift (diff=4.7550mm) — reset probe at 65.996,275.995 is z=354.472500 Tap drift (diff=10.2275mm) — reset probe at 65.996,275.995 is z=347.290000 Tap drift (diff=7.1825mm) — reset probe at 65.996,275.995 is z=335.817500 Tap drift (diff=11.4725mm) — reset probe at 65.996,275.995 is z=307.155000 Tap drift (diff=28.6625mm) — reset Tap OK (diff=0.0000mm, stable 2/5) probe at 65.996,275.995 is z=307.160000 Tap OK (diff=0.0050mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) probe at 65.996,275.995 is z=307.157500 Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=307.1575 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (66.0, 276.0) ~ point de tap (66.0, 276.0)

Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.999,275.995 is z=395.242500 probe at 65.999,275.995 is z=395.872500 Tap drift (diff=0.6300mm) — reset probe at 65.999,275.995 is z=0.827500 Tap drift (diff=395.0450mm) — reset probe at 65.999,275.995 is z=0.837500 Tap drift (diff=0.0100mm) — reset probe at 65.999,275.995 is z=0.835000 Tap OK (diff=0.0025mm, stable 2/5) probe at 65.999,275.995 is z=0.852500 Tap drift (diff=0.0175mm) — reset Tap OK (diff=0.0000mm, stable 2/5) probe at 65.999,275.995 is z=0.842500 Tap OK (diff=0.0100mm, stable 3/5) probe at 65.999,275.995 is z=3.812500 Tap drift (diff=2.9600mm) — reset probe at 65.999,275.995 is z=0.857500 Tap drift (diff=2.9550mm) — reset probe at 65.999,275.995 is z=2.747500 Tap drift (diff=1.8900mm) — reset probe at 65.999,275.995 is z=0.845000 Tap drift (diff=1.9025mm) — reset Tap OK (diff=0.0075mm, stable 2/5) probe at 65.999,275.995 is z=0.840000 Tap OK (diff=0.0025mm, stable 3/5) probe at 65.999,275.995 is z=0.850000 Tap drift (diff=0.0125mm) — reset Tap OK (diff=0.0075mm, stable 3/5) Tap OK (diff=0.0025mm, stable 4/5) probe at 65.999,275.995 is z=1.055000 Tap drift (diff=0.2050mm) — reset probe at 65.999,275.995 is z=0.855000 Tap drift (diff=0.2000mm) — reset probe at 65.999,275.995 is z=0.860000 Tap OK (diff=0.0050mm, stable 2/5) Switch encore declenche (vibration) -> attente 2.0s puis nouvelle tentative (1/10) probe at 65.999,275.995 is z=3.670000 Tap drift (diff=2.8100mm) — reset

probe: at 67.000,271.004 bed will contact at z=1.370000 probe: at 67.000,271.004 bed will contact at z=1.437500 Probe samples exceed tolerance. Retrying... probe: at 67.000,271.004 bed will contact at z=1.425000 probe: at 67.000,271.004 bed will contact at z=1.350000 probe: at 67.000,271.004 bed will contact at z=1.405000 probe: at 67.000,271.004 bed will contact at z=1.400000 probe: at 67.000,271.004 bed will contact at z=1.410000 probe: at 267.996,271.004 bed will contact at z=1.392500 probe: at 267.996,271.004 bed will contact at z=1.397500 probe: at 267.996,271.004 bed will contact at z=1.385000 probe: at 267.996,71.995 bed will contact at z=1.420000 probe: at 267.996,71.995 bed will contact at z=1.415000 probe: at 267.996,71.995 bed will contact at z=1.422500 probe: at 67.000,71.995 bed will contact at z=1.387500 probe: at 67.000,71.995 bed will contact at z=1.402500 probe: at 67.000,71.995 bed will contact at z=1.365000 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=84.0, y=241.0, z=1.40500 front right screw : x=285.0, y=241.0, z=1.39250 : adjust CCW 00:01 rear right screw : x=285.0, y=42.0, z=1.42000 : adjust CW 00:02 rear left screw : x=84.0, y=42.0, z=1.38750 : adjust CCW 00:02