[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C435;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22S148H;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=750;ssr=SSR10DA;lot=20260618;uid=9221AF [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=54002F001051353135323934

[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C435;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22S148H;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=750;ssr=SSR10DA;lot=20260618;uid=9221AF [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=54002F001051353135323934 Run Current: 0.98A Hold Current: 0.98A YUMI_SENSORLESS_HOME X: home base... (sgthrs=50) Run Current: 1.20A Hold Current: 1.09A tap 1: pos=467.0213 gap=1.9787 (chauffe, ignore) tap 2: pos=466.9969 gap=2.0031 (1/4) tap 3: pos=466.9969 gap=2.0031 (2/4) tap 4: pos=466.9969 gap=2.0031 (3/4) tap 5: pos=466.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=466.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=467.0000

Run Current: 1.20A Hold Current: 1.09A YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=466.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=467.0000 Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... (sgthrs=50) Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-21.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=-20.9969 gap=2.0031 (1/4) tap 3: pos=-20.9969 gap=2.0031 (2/4) tap 4: pos=-20.9969 gap=2.0031 (3/4) tap 5: pos=-20.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-20.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-21.0000

Run Current: 0.98A Hold Current: 0.98A YUMI_SENSORLESS_HOME X: home base... (sgthrs=50) Run Current: 1.20A Hold Current: 1.09A tap 1: pos=467.0091 gap=1.9909 (chauffe, ignore) tap 2: pos=467.1919 gap=1.8081 (1/4) tap 3: pos=466.9969 gap=2.0031 (2/4) tap 4: pos=466.9969 gap=2.0031 (3/4) tap 5: pos=466.8019 gap=2.1981 fenetre=0.3900/0.0500 tap 6: pos=467.1919 gap=1.8081 fenetre=0.3900/0.0500 tap 7: pos=466.9969 gap=2.0031 fenetre=0.3900/0.0500 tap 8: pos=466.9969 gap=2.0031 fenetre=0.3900/0.0500 tap 9: pos=466.9969 gap=2.0031 fenetre=0.1950/0.0500 tap 10: pos=466.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 9 taps valides (0 rejetes) -> moyenne=466.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=467.0000 Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... (sgthrs=50) Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-21.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=-20.9969 gap=2.0031 (1/4) tap 3: pos=-20.9969 gap=2.0031 (2/4) tap 4: pos=-20.9969 gap=2.0031 (3/4) tap 5: pos=-20.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-20.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-21.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 125mm + motion sensor YMS-2 OK

Extruder 'extruder1' now syncing with '' Run Current: 0.98A Hold Current: 0.98A YUMI_SENSORLESS_HOME X: home base... (sgthrs=50) Run Current: 1.20A Hold Current: 1.09A tap 1: pos=467.3991 gap=1.6009 (chauffe, ignore) tap 2: pos=466.9969 gap=2.0031 (1/4) tap 3: pos=466.8019 gap=2.1981 (2/4) tap 4: pos=467.1919 gap=1.8081 (3/4) tap 5: pos=466.9969 gap=2.0031 fenetre=0.3900/0.0500 tap 6: pos=466.9969 gap=2.0031 fenetre=0.3900/0.0500 tap 7: pos=466.9969 gap=2.0031 fenetre=0.1950/0.0500 tap 8: pos=466.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 7 taps valides (0 rejetes) -> moyenne=466.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=467.0000 Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... (sgthrs=50) Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-21.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=-20.9969 gap=2.0031 (1/4) tap 3: pos=-20.9969 gap=2.0031 (2/4) tap 4: pos=-20.9969 gap=2.0031 (3/4) tap 5: pos=-21.0091 gap=1.9909 fenetre=0.0122/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-20.9999 spread=0.0122mm (tol=0.0500). Zero pose en butee=-21.0000 Moving to tap point X=56.0 Y=334.0... Probing with pressure switch... probe at 55.998,334.001 is z=493.237500 probe at 55.998,334.001 is z=471.617500 Tap drift (diff=21.6200mm) — reset probe at 55.998,334.001 is z=386.222500 Tap drift (diff=85.3950mm) — reset probe at 55.998,334.001 is z=386.245000 Tap drift (diff=0.0225mm) — reset probe at 55.998,334.001 is z=386.282500 Tap drift (diff=0.0375mm) — reset probe at 55.998,334.001 is z=386.810000 Tap drift (diff=0.5275mm) — reset probe at 55.998,334.001 is z=389.602500 Tap drift (diff=2.7925mm) — reset probe at 55.998,334.001 is z=389.042500 Tap drift (diff=0.5600mm) — reset probe at 55.998,334.001 is z=390.960000 Tap drift (diff=1.9175mm) — reset probe at 55.998,334.001 is z=386.287500 Tap drift (diff=4.6725mm) — reset probe at 55.998,334.001 is z=386.252500 Tap drift (diff=0.0350mm) — reset probe at 55.998,334.001 is z=386.262500 Tap drift (diff=0.0100mm) — reset probe at 55.998,334.001 is z=386.265000 Tap OK (diff=0.0025mm, stable 2/5) probe at 55.998,334.001 is z=387.175000 Tap drift (diff=0.9100mm) — reset probe at 55.998,334.001 is z=386.250000 Tap drift (diff=0.9250mm) — reset probe at 55.998,334.001 is z=386.237500 Tap drift (diff=0.0125mm) — reset probe at 55.998,334.001 is z=386.227500 Tap OK (diff=0.0100mm, stable 2/5) probe at 55.998,334.001 is z=386.232500 Tap OK (diff=0.0050mm, stable 3/5) Switch encore declenche (vibration) -> attente 2.0s puis nouvelle tentative (1/10) probe at 55.998,334.001 is z=389.010000 Tap drift (diff=2.7775mm) — reset probe at 55.998,334.001 is z=391.805000 Tap drift (diff=2.7950mm) — reset probe at 55.998,334.001 is z=386.242500 Tap drift (diff=5.5625mm) — reset probe at 55.998,334.001 is z=386.230000 Tap OK (diff=0.0025mm, stable 4/5) probe at 55.998,334.001 is z=386.240000 Tap OK (diff=0.0025mm, stable 3/5) probe at 55.998,334.001 is z=388.827500 Tap drift (diff=2.5875mm) — reset probe at 55.998,334.001 is z=386.217500 Tap drift (diff=2.6100mm) — reset probe at 55.998,334.001 is z=386.235000 Tap OK (diff=0.0075mm, stable 4/5) probe at 55.998,334.001 is z=388.572500 Tap drift (diff=2.3375mm) — reset Tap drift (diff=2.3425mm) — reset probe at 55.998,334.001 is z=389.007500 Tap drift (diff=2.7650mm) — reset Tap OK (diff=0.0050mm, stable 2/5) Tap OK (diff=0.0000mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=386.2325 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (56.0, 334.0) ~ point de tap (56.0, 334.0) Z calibration complete!

Moving to tap point X=56.0 Y=334.0... Probing with pressure switch... probe at 56.001,334.001 is z=495.757500 probe at 56.001,334.001 is z=498.530000 Tap rejete (vibration chassis, z=498.5300 > max-z_hop) -> pas de remontee, on poursuit la descente (1) probe at 56.001,334.001 is z=459.230000 Switch encore declenche (vibration) -> attente 2.0s puis nouvelle tentative (1/10) Switch encore declenche (vibration) -> attente 2.0s puis nouvelle tentative (2/10) probe at 56.001,334.001 is z=341.242500 Tap drift (diff=117.9875mm) — reset probe at 56.001,334.001 is z=337.400000 Tap drift (diff=3.8425mm) — reset probe at 56.001,334.001 is z=339.992500 Tap drift (diff=2.5925mm) — reset probe at 56.001,334.001 is z=264.215000 Tap drift (diff=75.7775mm) — reset probe at 56.001,334.001 is z=265.935000 Tap drift (diff=1.7200mm) — reset probe at 56.001,334.001 is z=268.710000 Tap drift (diff=2.7750mm) — reset probe at 56.001,334.001 is z=198.980000 Tap drift (diff=69.7300mm) — reset probe at 56.001,334.001 is z=201.480000 Tap drift (diff=2.5000mm) — reset probe at 56.001,334.001 is z=157.325000 Tap drift (diff=44.1550mm) — reset probe at 56.001,334.001 is z=151.360000 Tap drift (diff=5.9650mm) — reset probe at 56.001,334.001 is z=1.090000 Tap drift (diff=150.2700mm) — reset probe at 56.001,334.001 is z=1.100000 Tap drift (diff=0.0100mm) — reset probe at 56.001,334.001 is z=1.102500 Tap OK (diff=0.0025mm, stable 2/5) probe at 56.001,334.001 is z=1.112500 Tap OK (diff=0.0000mm, stable 2/5) probe at 56.001,334.001 is z=1.707500 Tap drift (diff=0.5950mm) — reset probe at 56.001,334.001 is z=1.117500 Tap drift (diff=0.5900mm) — reset probe at 56.001,334.001 is z=4.065000 Tap drift (diff=2.9475mm) — reset probe at 56.001,334.001 is z=6.832500 Tap drift (diff=2.7675mm) — reset probe at 56.001,334.001 is z=9.640000 Tap drift (diff=2.8075mm) — reset probe at 56.001,334.001 is z=1.110000 Tap drift (diff=8.5300mm) — reset probe at 56.001,334.001 is z=1.132500 Tap drift (diff=0.0200mm) — reset Tap drift (diff=0.0150mm) — reset probe at 56.001,334.001 is z=1.125000 Tap OK (diff=0.0075mm, stable 2/5) probe at 56.001,334.001 is z=1.120000 Tap OK (diff=0.0050mm, stable 3/5) Tap OK (diff=0.0025mm, stable 4/5) probe at 56.001,334.001 is z=4.107500 Tap drift (diff=2.9900mm) — reset probe at 56.001,334.001 is z=6.027500 Tap drift (diff=1.9200mm) — reset Tap drift (diff=4.9150mm) — reset probe at 56.001,334.001 is z=1.115000 Tap OK (diff=0.0025mm, stable 3/5) probe at 56.001,334.001 is z=1.122500 Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=1.1200 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (56.0, 334.0) ~ point de tap (56.0, 334.0) Z calibration complete! probe at 56.001,334.001 is z=495.332500 probe at 56.001,334.001 is z=486.095000 Tap drift (diff=9.2375mm) — reset probe at 56.001,334.001 is z=486.107500 Tap drift (diff=0.0125mm) — reset probe at 56.001,334.001 is z=486.102500 Tap OK (diff=0.0050mm, stable 2/5) probe at 56.001,334.001 is z=486.100000 probe at 56.001,334.001 is z=486.097500 Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=486.1000 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Tap OK (diff=0.0000mm, stable 4/5) VALIDATED: trigger_z=486.1025 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Tap OK (diff=0.0075mm, stable 5/5) VALIDATED: trigger_z=486.1075 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Tap OK (diff=0.0000mm, stable 3/5) probe at 56.001,334.001 is z=486.092500 VALIDATED: trigger_z=486.0925 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) probe at 56.001,334.001 is z=486.110000 probe at 56.001,334.001 is z=486.105000 Tap OK (diff=0.0050mm, stable 4/5) VALIDATED: trigger_z=486.1100 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) VALIDATED: trigger_z=486.0950 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) probe at 56.001,334.001 is z=488.907500 Tap drift (diff=2.8025mm) — reset Tap drift (diff=2.8100mm) — reset probe at 56.001,334.001 is z=488.620000 Tap drift (diff=2.5225mm) — reset Tap drift (diff=2.5150mm) — reset probe at 56.001,334.001 is z=488.952500 Tap drift (diff=2.8475mm) — reset Tap drift (diff=2.8500mm) — reset Tap OK (diff=0.0050mm, stable 5/5) probe at 56.001,334.001 is z=488.887500 Tap drift (diff=2.7900mm) — reset Tap drift (diff=2.7875mm) — reset VALIDATED: trigger_z=486.1050 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Tap OK (diff=0.0075mm, stable 3/5) probe at 56.001,334.001 is z=488.602500 Tap drift (diff=2.4950mm) — reset Tap drift (diff=2.5050mm) — reset probe at 56.001,334.001 is z=486.090000 probe at 56.001,334.001 is z=486.907500 Tap drift (diff=0.8100mm) — reset Tap drift (diff=0.8125mm) — reset probe at 56.001,334.001 is z=487.790000 Tap drift (diff=1.6950mm) — reset Tap drift (diff=1.7000mm) — reset probe at 56.001,334.001 is z=488.882500 Tap drift (diff=2.7850mm) — reset Tap drift (diff=2.7825mm) — reset probe at 56.001,334.001 is z=495.795000 Tap drift (diff=9.6975mm) — reset Tap drift (diff=2.7925mm) — reset probe at 56.001,334.001 is z=495.790000 Tap drift (diff=9.6875mm) — reset

Maillage OK (config): zero_reference_position (56.0, 334.0) ~ point de tap (56.0, 334.0) Z calibration complete! probe: at 56.003,334.994 bed will contact at z=1.490000 probe: at 56.003,334.994 bed will contact at z=1.487500 probe: at 56.003,334.994 bed will contact at z=1.480000 probe: at 388.002,334.994 bed will contact at z=1.435000 probe: at 388.002,334.994 bed will contact at z=1.425000 probe: at 388.002,334.994 bed will contact at z=1.440000 probe: at 388.002,110.001 bed will contact at z=1.447500 probe: at 388.002,110.001 bed will contact at z=1.445000 probe: at 388.002,110.001 bed will contact at z=1.477500 probe: at 56.003,110.001 bed will contact at z=1.502500 probe: at 56.003,110.001 bed will contact at z=1.515000 probe: at 56.003,110.001 bed will contact at z=1.530000 probe: at 221.996,222.004 bed will contact at z=1.465000 probe: at 221.996,222.004 bed will contact at z=1.555000 Probe samples exceed tolerance. Retrying... probe: at 221.996,222.004 bed will contact at z=1.560000 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=73.0, y=305.0, z=1.48750 front right screw : x=405.0, y=305.0, z=1.43500 : adjust CCW 00:06 rear right screw : x=405.0, y=80.0, z=1.44750 : adjust CCW 00:05 rear left screw : x=73.0, y=80.0, z=1.51500 : adjust CW 00:03 rear middle screw : x=239.0, y=192.0, z=1.55500 : adjust CW 00:08