[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C335;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22DH;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=500;ssr=SSR10DA;lot=20260618;uid=36C6E9 [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=540059000C51353234323830

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.1919 gap=1.8081 (chauffe, ignore) tap 2: pos=-30.7769 gap=1.2231 (1/4) tap 3: pos=-30.7769 gap=1.2231 (2/4) tap 4: pos=-30.7769 gap=1.2231 (3/4) tap 5: pos=-30.7769 gap=1.2231 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-30.7769 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.2163 gap=1.7837 (chauffe, ignore) tap 2: pos=357.1919 gap=1.8081 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.1950/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=357.0456 spread=0.1950mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.5941 gap=1.4059 (chauffe, ignore) tap 2: pos=-30.7769 gap=1.2231 (1/4) tap 3: pos=-30.7891 gap=1.2109 (2/4) tap 4: pos=-30.7769 gap=1.2231 (3/4) tap 5: pos=-30.7647 gap=1.2353 fenetre=0.0244/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-30.7769 spread=0.0244mm (tol=0.0500). Zero pose en butee=-30.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.1675 gap=1.8325 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.996,275.995 is z=395.605000 probe at 65.996,275.995 is z=304.547500 Tap drift (diff=91.0575mm) — reset probe at 65.996,275.995 is z=304.585000 Tap drift (diff=0.0375mm) — reset probe at 65.996,275.995 is z=304.600000 Tap drift (diff=0.0150mm) — reset probe at 65.996,275.995 is z=304.607500 Tap OK (diff=0.0075mm, stable 2/5) probe at 65.996,275.995 is z=304.617500 Tap drift (diff=0.0100mm) — reset probe at 65.996,275.995 is z=304.625000 probe at 65.996,275.995 is z=304.627500 Tap OK (diff=0.0025mm, stable 3/5) probe at 65.996,275.995 is z=304.630000 Tap OK (diff=0.0025mm, stable 4/5) probe at 65.996,275.995 is z=304.632500 Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=304.6325 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (66.0, 276.0) ~ point de tap (66.0, 276.0) Z calibration complete!

Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.999,275.995 is z=395.730000 probe at 65.999,275.995 is z=347.840000 Tap drift (diff=47.8900mm) — reset probe at 65.999,275.995 is z=350.587500 Tap drift (diff=2.7475mm) — reset probe at 65.999,275.995 is z=353.192500 Tap drift (diff=2.6050mm) — reset probe at 65.999,275.995 is z=355.952500 Tap drift (diff=2.7600mm) — reset probe at 65.999,275.995 is z=345.392500 Tap drift (diff=10.5600mm) — reset probe at 65.999,275.995 is z=348.110000 Tap drift (diff=2.7175mm) — reset probe at 65.999,275.995 is z=342.685000 Tap drift (diff=5.4250mm) — reset probe at 65.999,275.995 is z=345.310000 Tap drift (diff=2.6250mm) — reset Switch encore declenche (vibration) -> attente 2.0s puis nouvelle tentative (1/10) probe at 65.999,275.995 is z=348.075000 Tap drift (diff=2.7650mm) — reset probe at 65.999,275.995 is z=350.875000 Tap drift (diff=2.8000mm) — reset probe at 65.999,275.995 is z=343.387500 Tap drift (diff=7.4875mm) — reset probe at 65.999,275.995 is z=346.157500 Tap drift (diff=2.7700mm) — reset probe at 65.999,275.995 is z=342.072500 Tap drift (diff=4.0850mm) — reset probe at 65.999,275.995 is z=338.535000 Tap drift (diff=3.5375mm) — reset probe at 65.999,275.995 is z=338.322500 Tap drift (diff=0.2125mm) — reset probe at 65.999,275.995 is z=331.352500 Tap drift (diff=6.9700mm) — reset probe at 65.999,275.995 is z=330.187500 Tap drift (diff=1.1650mm) — reset probe at 65.999,275.995 is z=332.792500 probe at 65.999,275.995 is z=162.517500

probe: at 67.000,271.004 bed will contact at z=1.652500 probe: at 67.000,271.004 bed will contact at z=1.670000 probe: at 67.000,271.004 bed will contact at z=1.667500 probe: at 267.996,271.004 bed will contact at z=1.557500 probe: at 267.996,271.004 bed will contact at z=1.567500 probe: at 267.996,271.004 bed will contact at z=1.575000 probe: at 267.996,71.995 bed will contact at z=1.662500 probe: at 267.996,71.995 bed will contact at z=1.667500 probe: at 67.000,71.995 bed will contact at z=1.717500 probe: at 67.000,71.995 bed will contact at z=1.720000 probe: at 67.000,71.995 bed will contact at z=1.730000 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=84.0, y=241.0, z=1.66750 front right screw : x=285.0, y=241.0, z=1.56750 : adjust CCW 00:12 rear right screw : x=285.0, y=42.0, z=1.66250 : adjust CCW 00:01 rear left screw : x=84.0, y=42.0, z=1.72000 : adjust CW 00:06