[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C235;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22DH;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=300;ssr=SSR10DA;lot=20260616;uid=61C229 [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=540068001051353135323934

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=256.1919 gap=1.8081 (1/4) tap 3: pos=255.8019 gap=2.1981 (2/4) tap 4: pos=255.9969 gap=2.0031 (3/4) tap 5: pos=255.9969 gap=2.0031 fenetre=0.3900/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=255.9969 spread=0.3900mm (tol=0.0500). Zero pose en butee=256.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.3991 gap=1.6009 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-30.1797 gap=1.8203 (3/4) tap 5: pos=-30.5941 gap=1.4059 fenetre=0.5972/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-30.1919 spread=0.5972mm (tol=0.0500). Zero pose en butee=-30.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.7769 gap=1.2231 (chauffe, ignore) tap 2: pos=255.9969 gap=2.0031 (1/4) tap 3: pos=255.9969 gap=2.0031 (2/4) tap 4: pos=255.9969 gap=2.0031 (3/4) tap 5: pos=255.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=255.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=256.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.1919 gap=1.8081 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.7769 gap=1.2231 (chauffe, ignore) tap 2: pos=255.9969 gap=2.0031 (1/4) tap 3: pos=255.9969 gap=2.0031 (2/4) tap 4: pos=255.9969 gap=2.0031 (3/4) tap 5: pos=255.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=255.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=256.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.1919 gap=1.8081 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Moving to tap point X=31.0 Y=212.0... Probing with pressure switch... probe at 31.003,211.998 is z=185.255000 probe at 31.003,211.998 is z=185.250000 Tap OK (diff=0.0050mm, stable 2/5) Tap OK (diff=0.0000mm, stable 3/5) probe at 31.003,211.998 is z=185.252500 Tap OK (diff=0.0025mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=185.2525 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (31.0, 212.0) ~ point de tap (31.0, 212.0) Z calibration complete!

Moving to tap point X=31.0 Y=212.0... Probing with pressure switch... probe at 30.994,211.998 is z=0.942500 Tap OK (diff=0.0000mm, stable 2/5) probe at 30.994,211.998 is z=0.905000 Tap drift (diff=0.0375mm) — reset probe at 30.994,211.998 is z=0.940000 Tap drift (diff=0.0350mm) — reset probe at 30.994,211.998 is z=0.900000 Tap drift (diff=0.0400mm) — reset Tap drift (diff=0.0425mm) — reset Tap OK (diff=0.0000mm, stable 3/5) probe at 30.994,211.998 is z=0.902500 Tap OK (diff=0.0025mm, stable 2/5) probe at 30.994,211.998 is z=0.935000 Tap OK (diff=0.0050mm, stable 3/5) Tap OK (diff=0.0050mm, stable 4/5) Tap OK (diff=0.0025mm, stable 3/5) probe at 30.994,211.998 is z=0.985000 Tap drift (diff=0.0450mm) — reset probe at 30.994,211.998 is z=0.932500 Tap OK (diff=0.0075mm, stable 3/5) probe at 30.994,211.998 is z=0.860000 Tap drift (diff=0.0725mm) — reset Switch encore declenche (vibration) -> attente 2.0s puis nouvelle tentative (1/10) probe at 30.994,211.998 is z=2.297500 Tap drift (diff=1.4375mm) — reset Switch encore declenche (vibration) -> attente 2.0s puis nouvelle tentative (2/10) Tap drift (diff=1.3550mm) — reset probe at 30.994,211.998 is z=0.937500 Tap OK (diff=0.0050mm, stable 2/5) probe at 30.994,211.998 is z=0.945000 Tap OK (diff=0.0100mm, stable 4/5) Tap drift (diff=0.0100mm) — reset probe at 30.994,211.998 is z=0.950000 probe at 30.994,211.998 is z=0.980000 Tap drift (diff=0.0300mm) — reset probe at 30.994,211.998 is z=0.947500 Tap OK (diff=0.0075mm, stable 4/5) Tap OK (diff=0.0075mm, stable 5/5)

probe: at 32.495,205.497 bed will contact at z=1.190000 probe: at 32.495,205.497 bed will contact at z=1.180000 probe: at 32.495,205.497 bed will contact at z=1.187500 probe: at 206.996,205.497 bed will contact at z=0.220000 probe: at 206.996,205.497 bed will contact at z=0.227500 probe: at 206.996,205.497 bed will contact at z=0.232500 probe: at 206.996,31.995 bed will contact at z=1.215000 probe: at 206.996,31.995 bed will contact at z=1.210000 probe: at 32.495,31.995 bed will contact at z=2.725000 probe: at 32.495,31.995 bed will contact at z=2.712500 probe: at 32.495,31.995 bed will contact at z=2.722500 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=49.5, y=175.5, z=1.18750 front right screw : x=224.0, y=175.5, z=0.22750 : adjust CCW 01:55 rear right screw : x=224.0, y=2.0, z=1.21500 : adjust CW 00:03 rear left screw : x=49.5, y=2.0, z=2.72250 : adjust CW 03:04