[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C435;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22S148H;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=110V;bedw=550;ssr=SSR10DA;lot=20260618;uid=2ACAAE [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=550041001051353135323934

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.2284 gap=1.7716 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=457.1919 gap=1.8081 fenetre=0.1950/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=457.0456 spread=0.1950mm (tol=0.0500). Zero pose en butee=457.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1 rejete: aucun contact sur 7.0mm (No trigger on probe after full movement) tap 2 rejete: aucun contact sur 7.0mm (No trigger on probe after full movement) YUMI_SENSORLESS_HOME Y: home de base suspect (pas de contact) -> re-home de recuperation 1/2 tap 3: pos=-30.7647 gap=1.2353 (chauffe, ignore) tap 4: pos=-29.9969 gap=2.0031 (1/4) tap 5: pos=-29.9969 gap=2.0031 (2/4) tap 6: pos=-29.9969 gap=2.0031 (3/4) tap 7: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (2 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.2163 gap=1.7837 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.3747 gap=1.6253 (chauffe, ignore) tap 2: pos=457.1919 gap=1.8081 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.1950/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=457.0456 spread=0.1950mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.995,340.003 is z=481.642500 probe at 49.995,340.003 is z=406.122500 Tap drift (diff=75.5200mm) — reset probe at 49.995,340.003 is z=406.125000 Tap OK (diff=0.0025mm, stable 2/5) probe at 49.995,340.003 is z=406.127500 Tap OK (diff=0.0025mm, stable 3/5) probe at 49.995,340.003 is z=406.130000 Tap OK (diff=0.0025mm, stable 4/5) probe at 49.995,340.003 is z=406.135000 Tap OK (diff=0.0050mm, stable 5/5) VALIDATED: trigger_z=406.1350 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (50.0, 340.0) ~ point de tap (50.0, 340.0) Z calibration complete!

Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.998,340.003 is z=495.642500 probe at 49.998,340.003 is z=498.280000 Tap rejete (vibration chassis, z=498.2800 > max-z_hop) -> pas de remontee, on poursuit la descente (1) probe at 49.998,340.003 is z=1.112500 probe at 49.998,340.003 is z=1.122500 Tap drift (diff=0.0100mm) — reset probe at 49.998,340.003 is z=1.125000 Tap OK (diff=0.0025mm, stable 2/5) probe at 49.998,340.003 is z=1.120000 Tap OK (diff=0.0050mm, stable 3/5) probe at 49.998,340.003 is z=1.127500 Tap OK (diff=0.0075mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=1.1275 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (50.0, 340.0) ~ point de tap (50.0, 340.0) Z calibration complete! probe at 49.998,340.003 is z=486.102500 Tap OK (diff=0.0000mm, stable 2/5) Tap OK (diff=0.0000mm, stable 3/5) probe at 49.998,340.003 is z=486.105000 Tap OK (diff=0.0025mm, stable 4/5) VALIDATED: trigger_z=486.1050 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Tap OK (diff=0.0000mm, stable 4/5) probe at 49.998,340.003 is z=486.107500 Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=486.1075 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) probe at 49.998,340.003 is z=493.205000 probe at 49.998,340.003 is z=490.530000 Tap drift (diff=2.6750mm) — reset Tap drift (diff=4.4275mm) — reset Tap OK (diff=0.0025mm, stable 3/5) probe at 49.998,340.003 is z=486.097500 Tap OK (diff=0.0050mm, stable 2/5) probe at 49.998,340.003 is z=486.100000 VALIDATED: trigger_z=486.1000 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) probe at 49.998,340.003 is z=486.095000 Tap OK (diff=0.0050mm, stable 4/5) Tap OK (diff=0.0050mm, stable 5/5)

probe: at 54.997,315.001 bed will contact at z=1.605000 probe: at 54.997,315.001 bed will contact at z=1.602500 probe: at 54.997,315.001 bed will contact at z=1.607500 probe: at 380.001,315.001 bed will contact at z=1.545000 probe: at 380.001,315.001 bed will contact at z=1.532500 probe: at 380.001,83.000 bed will contact at z=1.525000 probe: at 380.001,83.000 bed will contact at z=1.522500 probe: at 380.001,83.000 bed will contact at z=1.520000 probe: at 54.997,83.000 bed will contact at z=1.650000 probe: at 54.997,83.000 bed will contact at z=1.660000 probe: at 217.505,202.498 bed will contact at z=1.652500 probe: at 217.505,202.498 bed will contact at z=1.667500 probe: at 217.505,202.498 bed will contact at z=1.725000 Probe samples exceed tolerance. Retrying... probe: at 217.505,202.498 bed will contact at z=1.665000 probe: at 217.505,202.498 bed will contact at z=1.702500 probe: at 217.505,202.498 bed will contact at z=1.635000 probe: at 217.505,202.498 bed will contact at z=1.770000 probe: at 217.505,202.498 bed will contact at z=1.677500 probe: at 217.505,202.498 bed will contact at z=1.712500 probe: at 217.505,202.498 bed will contact at z=1.680000 probe: at 217.505,202.498 bed will contact at z=1.710000 probe: at 217.505,202.498 bed will contact at z=1.675000 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=72.0, y=285.0, z=1.60500 front right screw : x=397.0, y=285.0, z=1.54500 : adjust CCW 00:07 rear right screw : x=397.0, y=53.0, z=1.52250 : adjust CCW 00:10 rear left screw : x=72.0, y=53.0, z=1.65000 : adjust CW 00:05 rear left screw : x=234.5, y=172.5, z=1.68000 : adjust CW 00:09