[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C235;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22DH;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=300;ssr=SSR10DA;lot=20260616;uid=61C229 [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=550042001051353135323934

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.2163 gap=1.7837 (chauffe, ignore) tap 2: pos=256.3869 gap=1.6131 (1/4) tap 3: pos=255.9969 gap=2.0031 (2/4) tap 4: pos=255.9969 gap=2.0031 (3/4) tap 5: pos=255.9969 gap=2.0031 fenetre=0.3900/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=256.0944 spread=0.3900mm (tol=0.0500). Zero pose en butee=256.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1 rejete: cible atteinte sans buter (gap=0.8209) tap 2: pos=-29.9969 gap=2.0031 (chauffe, ignore) tap 3: pos=-29.9969 gap=2.0031 (1/4) tap 4: pos=-29.9969 gap=2.0031 (2/4) tap 5: pos=-29.9969 gap=2.0031 (3/4) tap 6: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (1 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.2163 gap=1.7837 (chauffe, ignore) tap 2: pos=256.3869 gap=1.6131 (1/4) tap 3: pos=255.6069 gap=2.3931 (2/4) tap 4: pos=256.3869 gap=1.6131 (3/4) tap 5: pos=255.6069 gap=2.3931 fenetre=0.7800/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=255.9969 spread=0.7800mm (tol=0.0500). Zero pose en butee=256.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.9719 gap=1.0281 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 50mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.2163 gap=1.7837 (chauffe, ignore) tap 2: pos=255.9969 gap=2.0031 (1/4) tap 3: pos=255.9969 gap=2.0031 (2/4) tap 4: pos=255.9969 gap=2.0031 (3/4) tap 5: pos=255.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=255.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=256.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.9719 gap=1.0281 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Moving to tap point X=31.0 Y=212.0... Probing with pressure switch... probe at 31.003,211.998 is z=265.457500 probe at 31.003,211.998 is z=176.070000 Tap drift (diff=89.3875mm) — reset probe at 31.003,211.998 is z=176.077500 Tap OK (diff=0.0075mm, stable 2/5) probe at 31.003,211.998 is z=176.080000 Tap OK (diff=0.0025mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) probe at 31.003,211.998 is z=176.082500 Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=176.0825 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (31.0, 212.0) ~ point de tap (31.0, 212.0) Z calibration complete!

Moving to tap point X=31.0 Y=212.0... Probing with pressure switch... probe at 30.994,211.998 is z=249.042500 probe at 30.994,211.998 is z=0.877500 Tap drift (diff=248.1650mm) — reset probe at 30.994,211.998 is z=0.890000 Tap drift (diff=0.0125mm) — reset Tap OK (diff=0.0000mm, stable 2/5) Tap OK (diff=0.0000mm, stable 3/5) probe at 30.994,211.998 is z=0.892500 Tap OK (diff=0.0025mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=0.8925 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (31.0, 212.0) ~ point de tap (31.0, 212.0) Z calibration complete! probe at 30.994,211.998 is z=265.562500 probe at 30.994,211.998 is z=255.902500 Tap drift (diff=9.6600mm) — reset probe at 30.994,211.998 is z=258.045000 Tap drift (diff=2.1425mm) — reset probe at 30.994,211.998 is z=255.887500 Tap drift (diff=2.1575mm) — reset probe at 30.994,211.998 is z=258.875000 Tap drift (diff=2.9875mm) — reset probe at 30.994,211.998 is z=255.897500 Tap drift (diff=2.9775mm) — reset Tap OK (diff=0.0050mm, stable 2/5) probe at 30.994,211.998 is z=255.895000 Tap OK (diff=0.0075mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) probe at 30.994,211.998 is z=255.900000 Tap OK (diff=0.0050mm, stable 5/5) VALIDATED: trigger_z=255.9000 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) probe at 30.994,211.998 is z=255.907500 probe at 30.994,211.998 is z=255.905000 Tap OK (diff=0.0025mm, stable 2/5) probe at 30.994,211.998 is z=258.287500 Tap drift (diff=2.3825mm) — reset probe at 30.994,211.998 is z=260.047500 Tap drift (diff=1.7600mm) — reset

probe: at 32.495,205.497 bed will contact at z=0.762500 probe: at 32.495,205.497 bed will contact at z=1.017500 Probe samples exceed tolerance. Retrying... probe: at 32.495,205.497 bed will contact at z=1.020000 probe: at 32.495,205.497 bed will contact at z=1.025000 probe: at 206.996,205.497 bed will contact at z=1.770000 probe: at 206.996,205.497 bed will contact at z=2.057500 probe: at 206.996,205.497 bed will contact at z=2.040000 probe: at 206.996,205.497 bed will contact at z=2.030000 probe: at 206.996,205.497 bed will contact at z=2.035000 probe: at 206.996,31.995 bed will contact at z=1.795000 probe: at 206.996,31.995 bed will contact at z=2.080000 probe: at 206.996,31.995 bed will contact at z=2.060000 probe: at 206.996,31.995 bed will contact at z=2.055000 probe: at 206.996,31.995 bed will contact at z=2.057500 probe: at 32.495,31.995 bed will contact at z=1.302500 probe: at 32.495,31.995 bed will contact at z=1.565000 probe: at 32.495,31.995 bed will contact at z=1.560000 probe: at 32.495,31.995 bed will contact at z=1.557500 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=49.5, y=175.5, z=1.02000 front right screw : x=224.0, y=175.5, z=2.03500 : adjust CW 02:02 rear right screw : x=224.0, y=2.0, z=2.05750 : adjust CW 02:05 rear left screw : x=49.5, y=2.0, z=1.56000 : adjust CW 01:05