[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C435;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22S148H;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=110V;bedw=550;ssr=SSR10DA;lot=20260618;uid=2ACAAE [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=550060001051353135323934

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.5941 gap=1.4059 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-17.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-17.9969 gap=2.0031 (1/4) tap 3: pos=-18.3747 gap=1.6253 (2/4) tap 4: pos=-18.7769 gap=1.2231 (3/4) tap 5: pos=-18.3991 gap=1.6009 fenetre=0.7800/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-18.3869 spread=0.7800mm (tol=0.0500). Zero pose en butee=-18.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.5941 gap=1.4059 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-17.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-17.9969 gap=2.0031 (1/4) tap 3: pos=-17.9969 gap=2.0031 (2/4) tap 4: pos=-17.9969 gap=2.0031 (3/4) tap 5: pos=-17.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-17.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-18.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.0213 gap=1.9787 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=457.5697 gap=1.4303 (2/4) tap 4: pos=457.7769 gap=1.2231 (3/4) tap 5: pos=457.7769 gap=1.2231 fenetre=0.7800/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=457.5301 spread=0.7800mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-17.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-17.9969 gap=2.0031 (1/4) tap 3: pos=-17.9969 gap=2.0031 (2/4) tap 4: pos=-17.9969 gap=2.0031 (3/4) tap 5: pos=-17.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-17.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-18.0000 Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.995,339.999 is z=386.412500 probe at 49.995,339.999 is z=389.225000 Tap drift (diff=2.8125mm) — reset probe at 49.995,339.999 is z=386.440000 Tap drift (diff=2.7850mm) — reset probe at 49.995,339.999 is z=386.500000 Tap drift (diff=0.0600mm) — reset probe at 49.995,339.999 is z=386.470000 Tap drift (diff=0.0300mm) — reset probe at 49.995,339.999 is z=386.445000 Tap drift (diff=0.0250mm) — reset probe at 49.995,339.999 is z=386.447500 Tap OK (diff=0.0025mm, stable 2/5) Tap OK (diff=0.0025mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=386.4475 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (50.0, 340.0) ~ point de tap (50.0, 340.0) Z calibration complete!

Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.998,339.999 is z=164.640000 probe at 49.998,339.999 is z=161.715000 Tap drift (diff=2.9250mm) — reset probe at 49.998,339.999 is z=6.867500 Tap drift (diff=154.8475mm) — reset probe at 49.998,339.999 is z=9.672500 Tap drift (diff=2.8050mm) — reset probe at 49.998,339.999 is z=12.480000 Tap drift (diff=2.8075mm) — reset probe at 49.998,339.999 is z=15.275000 Tap drift (diff=2.7950mm) — reset probe at 49.998,339.999 is z=17.790000 Tap drift (diff=2.5150mm) — reset probe at 49.998,339.999 is z=6.880000 Tap drift (diff=10.9100mm) — reset probe at 49.998,339.999 is z=6.892500 Tap drift (diff=0.0125mm) — reset probe at 49.998,339.999 is z=6.895000 Tap OK (diff=0.0025mm, stable 2/5) Tap OK (diff=0.0000mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=6.8950 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (50.0, 340.0) ~ point de tap (50.0, 340.0) Z calibration complete! probe at 49.998,339.999 is z=486.087500 probe at 49.998,339.999 is z=486.100000 probe at 49.998,339.999 is z=486.102500 probe at 49.998,339.999 is z=486.105000 Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=486.1050 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) probe at 49.998,339.999 is z=486.097500 Tap drift (diff=0.0100mm) — reset Tap OK (diff=0.0000mm, stable 2/5) Tap OK (diff=0.0050mm, stable 3/5) VALIDATED: trigger_z=486.1025 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) probe at 49.998,339.999 is z=486.085000 Tap OK (diff=0.0050mm, stable 2/5)

probe: at 54.997,328.001 bed will contact at z=1.490000 probe: at 54.997,328.001 bed will contact at z=1.475000 probe: at 54.997,328.001 bed will contact at z=1.525000 Probe samples exceed tolerance. Retrying... probe: at 54.997,328.001 bed will contact at z=1.495000 probe: at 54.997,328.001 bed will contact at z=1.455000 probe: at 54.997,328.001 bed will contact at z=1.467500 probe: at 380.001,328.001 bed will contact at z=1.322500 probe: at 380.001,328.001 bed will contact at z=1.335000 probe: at 380.001,328.001 bed will contact at z=1.332500 probe: at 380.001,101.996 bed will contact at z=1.320000 probe: at 380.001,101.996 bed will contact at z=1.325000 probe: at 380.001,101.996 bed will contact at z=1.340000 probe: at 54.997,101.996 bed will contact at z=1.577500 probe: at 54.997,101.996 bed will contact at z=1.590000 probe: at 54.997,101.996 bed will contact at z=1.600000 probe: at 217.505,214.498 bed will contact at z=1.405000 probe: at 217.505,214.498 bed will contact at z=1.407500 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=72.0, y=298.0, z=1.46750 front right screw : x=397.0, y=298.0, z=1.33250 : adjust CCW 00:16 rear right screw : x=397.0, y=72.0, z=1.32500 : adjust CCW 00:17 rear left screw : x=72.0, y=72.0, z=1.59000 : adjust CW 00:15 middle : x=234.5, y=184.5, z=1.40500 : adjust CCW 00:07