[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C335;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22DH;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=110V;bedw=500;ssr=SSR10DA;lot=20260618;uid=B3D7BD [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=55006C001051353135323934

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=357.1797 gap=1.8203 (3/4) tap 5: pos=356.8141 gap=2.1859 fenetre=0.3656/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.3656mm (tol=0.0500). Zero pose en butee=357.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.1797 gap=1.8203 (chauffe, ignore) tap 2: pos=-30.7769 gap=1.2231 (1/4) tap 3: pos=-30.7891 gap=1.2109 (2/4) tap 4: pos=-30.7647 gap=1.2353 (3/4) tap 5: pos=-30.7891 gap=1.2109 fenetre=0.0244/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-30.7799 spread=0.0244mm (tol=0.0500). Zero pose en butee=-30.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=357.1797 gap=1.8203 (2/4) tap 4: pos=356.8141 gap=2.1859 (3/4) tap 5: pos=357.1797 gap=1.8203 fenetre=0.3656/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=357.0426 spread=0.3656mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.1919 gap=1.8081 (chauffe, ignore) tap 2: pos=-30.7769 gap=1.2231 (1/4) tap 3: pos=-30.7647 gap=1.2353 (2/4) tap 4: pos=-30.7769 gap=1.2231 (3/4) tap 5: pos=-30.7769 gap=1.2231 fenetre=0.0122/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-30.7738 spread=0.0122mm (tol=0.0500). Zero pose en butee=-30.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.5941 gap=1.4059 (chauffe, ignore) tap 2: pos=356.8141 gap=2.1859 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=357.1797 gap=1.8203 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.3656/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.3656mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.5697 gap=1.4303 (chauffe, ignore) tap 2: pos=-30.7891 gap=1.2109 (1/4) tap 3: pos=-30.7647 gap=1.2353 (2/4) tap 4: pos=-30.7891 gap=1.2109 (3/4) tap 5: pos=-30.7769 gap=1.2231 fenetre=0.0244/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-30.7799 spread=0.0244mm (tol=0.0500). Zero pose en butee=-30.0000 Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.996,275.995 is z=296.015000 probe at 65.996,275.995 is z=296.022500 Tap OK (diff=0.0075mm, stable 2/5) Tap OK (diff=0.0000mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=296.0225 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (66.0, 276.0) ~ point de tap (66.0, 276.0) Z calibration complete!

Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.999,275.995 is z=365.845000 probe at 65.999,275.995 is z=0.935000 Tap drift (diff=364.9100mm) — reset probe at 65.999,275.995 is z=0.955000 Tap drift (diff=0.0200mm) — reset probe at 65.999,275.995 is z=3.712500 Tap drift (diff=2.7575mm) — reset probe at 65.999,275.995 is z=0.960000 Tap drift (diff=2.7525mm) — reset probe at 65.999,275.995 is z=0.962500 Tap OK (diff=0.0025mm, stable 2/5) probe at 65.999,275.995 is z=3.715000 probe at 65.999,275.995 is z=0.965000 Tap drift (diff=2.7500mm) — reset probe at 65.999,275.995 is z=3.717500 probe at 65.999,275.995 is z=0.967500 probe at 65.999,275.995 is z=0.970000 probe at 65.999,275.995 is z=3.557500 Tap drift (diff=2.5875mm) — reset Tap OK (diff=0.0000mm, stable 2/5) probe at 65.999,275.995 is z=3.415000 Tap drift (diff=2.4450mm) — reset Tap drift (diff=2.4525mm) — reset probe at 65.999,275.995 is z=0.957500 Tap OK (diff=0.0050mm, stable 2/5) Tap OK (diff=0.0000mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=0.9575 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (66.0, 276.0) ~ point de tap (66.0, 276.0) Z calibration complete! probe at 65.999,275.995 is z=385.902500 probe at 65.999,275.995 is z=385.905000 Tap OK (diff=0.0025mm, stable 4/5) Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=385.9050 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) probe at 65.999,275.995 is z=385.900000 VALIDATED: trigger_z=385.9000 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000)

probe: at 67.000,271.004 bed will contact at z=2.110000 probe: at 67.000,271.004 bed will contact at z=2.122500 probe: at 67.000,271.004 bed will contact at z=2.117500 probe: at 267.996,271.004 bed will contact at z=1.957500 probe: at 267.996,271.004 bed will contact at z=1.962500 probe: at 267.996,271.004 bed will contact at z=1.960000 probe: at 267.996,71.995 bed will contact at z=2.015000 probe: at 267.996,71.995 bed will contact at z=2.012500 probe: at 67.000,71.995 bed will contact at z=2.030000 probe: at 67.000,71.995 bed will contact at z=2.042500 probe: at 67.000,71.995 bed will contact at z=2.035000 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=84.0, y=241.0, z=2.11750 front right screw : x=285.0, y=241.0, z=1.96000 : adjust CCW 00:19 rear right screw : x=285.0, y=42.0, z=2.01500 : adjust CCW 00:12 rear left screw : x=84.0, y=42.0, z=2.03500 : adjust CCW 00:10