[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C335;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22DH;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=110V;bedw=500;ssr=SSR10DA;lot=20260618;uid=B3D7BD [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=56006D001051353135323934

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.2163 gap=1.7837 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.8019 gap=2.1981 (2/4) tap 4: pos=357.1919 gap=1.8081 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.3900/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.3900mm (tol=0.0500). Zero pose en butee=357.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-29.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-30.3869 gap=1.6131 (1/4) tap 3: pos=-30.3869 gap=1.6131 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.3900/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-30.1919 spread=0.3900mm (tol=0.0500). Zero pose en butee=-30.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.3869 gap=1.6131 (chauffe, ignore) tap 2: pos=357.1919 gap=1.8081 (1/4) tap 3: pos=356.8019 gap=2.1981 (2/4) tap 4: pos=357.1919 gap=1.8081 (3/4) tap 5: pos=356.8019 gap=2.1981 fenetre=0.3900/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.3900mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-29.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.3747 gap=1.6253 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-29.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.996,275.995 is z=395.765000 probe at 65.996,275.995 is z=398.522500 Tap rejete (vibration chassis, z=398.5225 > max-z_hop) -> pas de remontee, on poursuit la descente (1) probe at 65.996,275.995 is z=286.207500 probe at 65.996,275.995 is z=286.205000 Tap OK (diff=0.0025mm, stable 2/5) probe at 65.996,275.995 is z=286.200000 Tap OK (diff=0.0050mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) probe at 65.996,275.995 is z=286.202500 Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=286.2025 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (66.0, 276.0) ~ point de tap (66.0, 276.0) Z calibration complete!

Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.999,275.995 is z=395.700000 probe at 65.999,275.995 is z=398.422500 Tap rejete (vibration chassis, z=398.4225 > max-z_hop) -> pas de remontee, on poursuit la descente (1) probe at 65.999,275.995 is z=68.335000 probe at 65.999,275.995 is z=71.065000 Tap drift (diff=2.7300mm) — reset probe at 65.999,275.995 is z=73.822500 Tap drift (diff=2.7575mm) — reset probe at 65.999,275.995 is z=76.585000 Tap drift (diff=2.7625mm) — reset probe at 65.999,275.995 is z=79.345000 Tap drift (diff=2.7600mm) — reset probe at 65.999,275.995 is z=82.107500 probe at 65.999,275.995 is z=84.867500 probe at 65.999,275.995 is z=87.627500 probe at 65.999,275.995 is z=90.387500 probe at 65.999,275.995 is z=93.147500 probe at 65.999,275.995 is z=95.905000 probe at 65.999,275.995 is z=98.662500 probe at 65.999,275.995 is z=101.425000 probe at 65.999,275.995 is z=41.132500 Tap drift (diff=60.2925mm) — reset Switch encore declenche (vibration) -> attente 2.0s puis nouvelle tentative (1/10) probe at 65.999,275.995 is z=43.862500 probe at 65.999,275.995 is z=32.420000 Tap drift (diff=11.4425mm) — reset probe at 65.999,275.995 is z=1.097500 Tap drift (diff=31.3225mm) — reset probe at 65.999,275.995 is z=1.095000 Tap OK (diff=0.0025mm, stable 2/5) Tap OK (diff=0.0000mm, stable 3/5) probe at 65.999,275.995 is z=1.100000 Tap OK (diff=0.0050mm, stable 4/5) probe at 65.999,275.995 is z=1.090000 Tap OK (diff=0.0100mm, stable 5/5) VALIDATED: trigger_z=1.0900 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (66.0, 276.0) ~ point de tap (66.0, 276.0) Z calibration complete!

probe: at 67.000,271.004 bed will contact at z=2.195000 probe: at 67.000,271.004 bed will contact at z=2.187500 probe: at 67.000,271.004 bed will contact at z=2.220000 probe: at 267.996,271.004 bed will contact at z=2.050000 probe: at 267.996,271.004 bed will contact at z=2.057500 probe: at 267.996,271.004 bed will contact at z=2.047500 probe: at 267.996,71.995 bed will contact at z=2.145000 probe: at 267.996,71.995 bed will contact at z=2.147500 probe: at 267.996,71.995 bed will contact at z=2.130000 probe: at 67.000,71.995 bed will contact at z=2.150000 probe: at 67.000,71.995 bed will contact at z=2.152500 probe: at 67.000,71.995 bed will contact at z=2.182500 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=84.0, y=241.0, z=2.19500 front right screw : x=285.0, y=241.0, z=2.05000 : adjust CCW 00:17 rear right screw : x=285.0, y=42.0, z=2.14500 : adjust CCW 00:06 rear left screw : x=84.0, y=42.0, z=2.15250 : adjust CCW 00:05