[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C435;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22S148H;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=110V;bedw=550;ssr=SSR10DA;lot=20260618;uid=2ACAAE [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=570059001051353135323934

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.8141 gap=2.1859 (3/4) tap 5: pos=457.1797 gap=1.8203 fenetre=0.3656/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.3656mm (tol=0.0500). Zero pose en butee=457.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.5819 gap=1.4181 (chauffe, ignore) tap 2: pos=-17.9969 gap=2.0031 (1/4) tap 3: pos=-17.9969 gap=2.0031 (2/4) tap 4: pos=-17.9969 gap=2.0031 (3/4) tap 5: pos=-17.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-17.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-18.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.5697 gap=1.4303 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=457.1797 gap=1.8203 (2/4) tap 4: pos=456.8141 gap=2.1859 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.3656/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.3656mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-17.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-17.9969 gap=2.0031 (1/4) tap 3: pos=-17.9969 gap=2.0031 (2/4) tap 4: pos=-17.9969 gap=2.0031 (3/4) tap 5: pos=-17.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-17.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-18.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.5819 gap=1.4181 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=457.1797 gap=1.8203 (2/4) tap 4: pos=456.8141 gap=2.1859 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.3656/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.3656mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-17.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-17.9969 gap=2.0031 (1/4) tap 3: pos=-17.9969 gap=2.0031 (2/4) tap 4: pos=-17.9969 gap=2.0031 (3/4) tap 5: pos=-17.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-17.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-18.0000 Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.995,339.999 is z=384.420000 probe at 49.995,339.999 is z=384.437500 Tap drift (diff=0.0175mm) — reset Tap OK (diff=0.0000mm, stable 2/5) probe at 49.995,339.999 is z=384.450000 Tap drift (diff=0.0125mm) — reset probe at 49.995,339.999 is z=384.467500 probe at 49.995,339.999 is z=384.470000 Tap OK (diff=0.0025mm, stable 2/5) probe at 49.995,339.999 is z=384.482500 probe at 49.995,339.999 is z=384.472500 Tap OK (diff=0.0100mm, stable 2/5) Tap drift (diff=0.0100mm) — reset probe at 49.995,339.999 is z=384.477500 Tap OK (diff=0.0050mm, stable 2/5) probe at 49.995,339.999 is z=384.475000 Tap OK (diff=0.0025mm, stable 3/5) probe at 49.995,339.999 is z=384.485000 probe at 49.995,339.999 is z=384.492500 Tap OK (diff=0.0075mm, stable 2/5) probe at 49.995,339.999 is z=384.495000

Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.998,339.999 is z=0.840000 probe at 49.998,339.999 is z=0.857500 Tap drift (diff=0.0175mm) — reset probe at 49.998,339.999 is z=0.867500 Tap drift (diff=0.0100mm) — reset probe at 49.998,339.999 is z=0.880000 Tap drift (diff=0.0125mm) — reset probe at 49.998,339.999 is z=0.877500 Tap OK (diff=0.0025mm, stable 2/5) probe at 49.998,339.999 is z=0.890000 probe at 49.998,339.999 is z=0.892500 probe at 49.998,339.999 is z=0.887500 Tap OK (diff=0.0050mm, stable 3/5) Tap OK (diff=0.0025mm, stable 4/5) probe at 49.998,339.999 is z=0.895000 Tap OK (diff=0.0050mm, stable 5/5) VALIDATED: trigger_z=0.8950 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (50.0, 340.0) ~ point de tap (50.0, 340.0) Z calibration complete! probe at 49.998,339.999 is z=485.865000 probe at 49.998,339.999 is z=485.892500 Tap drift (diff=0.0275mm) — reset probe at 49.998,339.999 is z=485.895000 probe at 49.998,339.999 is z=485.900000 Tap OK (diff=0.0075mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=485.8925 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) probe at 49.998,339.999 is z=485.875000 probe at 49.998,339.999 is z=485.910000 Tap drift (diff=0.0350mm) — reset probe at 49.998,339.999 is z=485.902500 Tap OK (diff=0.0075mm, stable 2/5) probe at 49.998,339.999 is z=485.907500 probe at 49.998,339.999 is z=485.912500 Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=485.9125 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) probe at 49.998,339.999 is z=485.867500 probe at 49.998,339.999 is z=485.897500

probe: at 54.997,328.001 bed will contact at z=1.457500 probe: at 54.997,328.001 bed will contact at z=1.475000 probe: at 54.997,328.001 bed will contact at z=1.467500 probe: at 380.001,328.001 bed will contact at z=1.500000 probe: at 380.001,328.001 bed will contact at z=1.492500 probe: at 380.001,101.996 bed will contact at z=1.460000 probe: at 380.001,101.996 bed will contact at z=1.447500 probe: at 380.001,101.996 bed will contact at z=1.462500 probe: at 54.997,101.996 bed will contact at z=1.462500 probe: at 54.997,101.996 bed will contact at z=1.470000 probe: at 54.997,101.996 bed will contact at z=1.472500 probe: at 217.505,214.498 bed will contact at z=1.510000 probe: at 217.505,214.498 bed will contact at z=1.505000 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=72.0, y=298.0, z=1.46750 front right screw : x=397.0, y=298.0, z=1.49250 : adjust CW 00:03 rear right screw : x=397.0, y=72.0, z=1.46000 : adjust CCW 00:01 rear left screw : x=72.0, y=72.0, z=1.47000 : adjust CW 00:00 middle : x=234.5, y=184.5, z=1.50500 : adjust CW 00:05