[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C235;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22DH;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=300;ssr=SSR10DA;lot=20260616;uid=61C229 [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=570067001051353135323934

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.5941 gap=1.4059 (chauffe, ignore) tap 2: pos=255.9969 gap=2.0031 (1/4) tap 3: pos=255.9969 gap=2.0031 (2/4) tap 4: pos=255.9969 gap=2.0031 (3/4) tap 5: pos=255.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=255.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=256.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1 rejete: aucun contact sur 7.0mm (No trigger on probe after full movement) tap 2 rejete: aucun contact sur 7.0mm (No trigger on probe after full movement) YUMI_SENSORLESS_HOME Y: home de base suspect (pas de contact) -> re-home de recuperation 1/2 tap 3: pos=-30.5697 gap=1.4303 (chauffe, ignore) tap 4: pos=-30.5941 gap=1.4059 (1/4) tap 5: pos=-30.1797 gap=1.8203 (2/4) tap 6: pos=-29.9969 gap=2.0031 (3/4) tap 7: pos=-29.9969 gap=2.0031 fenetre=0.5972/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (2 rejetes) -> moyenne=-30.1919 spread=0.5972mm (tol=0.0500). Zero pose en butee=-30.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=255.9969 gap=2.0031 (1/4) tap 3: pos=256.1797 gap=1.8203 (2/4) tap 4: pos=255.8141 gap=2.1859 (3/4) tap 5: pos=255.9969 gap=2.0031 fenetre=0.3656/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=255.9969 spread=0.3656mm (tol=0.0500). Zero pose en butee=256.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.9597 gap=1.0403 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 50mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=255.9969 gap=2.0031 (1/4) tap 3: pos=255.9969 gap=2.0031 (2/4) tap 4: pos=255.9969 gap=2.0031 (3/4) tap 5: pos=255.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=255.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=256.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.7769 gap=1.2231 (chauffe, ignore) tap 2: pos=-30.1797 gap=1.8203 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.1828/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-30.0426 spread=0.1828mm (tol=0.0500). Zero pose en butee=-30.0000 Moving to tap point X=31.0 Y=212.0... Probing with pressure switch... probe at 31.003,211.998 is z=176.025000 probe at 31.003,211.998 is z=176.047500 Tap drift (diff=0.0225mm) — reset probe at 31.003,211.998 is z=176.050000 Tap OK (diff=0.0025mm, stable 2/5) probe at 31.003,211.998 is z=176.052500 Tap OK (diff=0.0025mm, stable 3/5) probe at 31.003,211.998 is z=176.055000 Tap OK (diff=0.0025mm, stable 4/5) probe at 31.003,211.998 is z=176.057500 Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=176.0575 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (31.0, 212.0) ~ point de tap (31.0, 212.0) Z calibration complete!

Moving to tap point X=31.0 Y=212.0... Probing with pressure switch... probe at 30.994,211.998 is z=265.375000 probe at 30.994,211.998 is z=252.817500 Tap drift (diff=12.5575mm) — reset Switch encore declenche (vibration) -> attente 2.0s puis nouvelle tentative (1/10) probe at 30.994,211.998 is z=255.032500 Tap drift (diff=2.2150mm) — reset probe at 30.994,211.998 is z=255.987500 Tap drift (diff=0.9550mm) — reset probe at 30.994,211.998 is z=205.620000 Tap drift (diff=50.3675mm) — reset probe at 30.994,211.998 is z=203.830000 Tap drift (diff=1.7900mm) — reset probe at 30.994,211.998 is z=201.790000 Tap drift (diff=2.0400mm) — reset probe at 30.994,211.998 is z=0.910000 Tap drift (diff=200.8800mm) — reset probe at 30.994,211.998 is z=0.942500 Tap drift (diff=0.0325mm) — reset probe at 30.994,211.998 is z=0.947500 Tap OK (diff=0.0050mm, stable 2/5) probe at 30.994,211.998 is z=0.962500 Tap drift (diff=0.0150mm) — reset probe at 30.994,211.998 is z=0.970000 Tap OK (diff=0.0075mm, stable 2/5) Tap OK (diff=0.0000mm, stable 3/5) probe at 30.994,211.998 is z=0.972500 Tap OK (diff=0.0025mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=0.9725 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (31.0, 212.0) ~ point de tap (31.0, 212.0) Z calibration complete! probe at 30.994,211.998 is z=255.815000 probe at 30.994,211.998 is z=255.900000 Tap drift (diff=0.0850mm) — reset probe at 30.994,211.998 is z=255.902500 Tap OK (diff=0.0025mm, stable 2/5) Tap OK (diff=0.0000mm, stable 4/5) VALIDATED: trigger_z=255.9025 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000)

probe: at 32.495,205.497 bed will contact at z=1.375000 probe: at 32.495,205.497 bed will contact at z=1.445000 Probe samples exceed tolerance. Retrying... probe: at 32.495,205.497 bed will contact at z=1.430000 probe: at 32.495,205.497 bed will contact at z=1.452500 probe: at 206.996,205.497 bed will contact at z=4.317500 probe: at 206.996,205.497 bed will contact at z=4.350000 probe: at 206.996,205.497 bed will contact at z=4.360000 probe: at 206.996,31.995 bed will contact at z=5.132500 probe: at 206.996,31.995 bed will contact at z=5.165000 probe: at 206.996,31.995 bed will contact at z=5.172500 probe: at 32.495,31.995 bed will contact at z=2.990000 probe: at 32.495,31.995 bed will contact at z=2.985000 probe: at 32.495,31.995 bed will contact at z=3.047500 probe: at 32.495,31.995 bed will contact at z=3.012500 probe: at 32.495,31.995 bed will contact at z=3.055000 probe: at 32.495,31.995 bed will contact at z=3.072500 probe: at 32.495,31.995 bed will contact at z=3.097500 probe: at 32.495,31.995 bed will contact at z=3.010000 probe: at 32.495,31.995 bed will contact at z=3.070000 probe: at 32.495,31.995 bed will contact at z=3.005000 probe: at 32.495,31.995 bed will contact at z=3.082500 probe: at 32.495,31.995 bed will contact at z=2.975000 probe: at 32.495,31.995 bed will contact at z=3.045000 probe: at 32.495,31.995 bed will contact at z=3.017500 probe: at 32.495,31.995 bed will contact at z=3.050000 probe: at 32.495,31.995 bed will contact at z=3.075000 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=49.5, y=175.5, z=1.43000 front right screw : x=224.0, y=175.5, z=4.35000 : adjust CW 05:50 rear right screw : x=224.0, y=2.0, z=5.16500 : adjust CW 07:28 rear left screw : x=49.5, y=2.0, z=3.05000 : adjust CW 03:14