[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C435;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22S148H;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=750;ssr=SSR10DA;lot=20260618;uid=9221AF [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=57006B001051353135323934

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.7525 gap=1.2475 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-17.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-17.9969 gap=2.0031 (1/4) tap 3: pos=-17.9969 gap=2.0031 (2/4) tap 4: pos=-17.9969 gap=2.0031 (3/4) tap 5: pos=-17.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-17.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-18.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-17.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-17.9969 gap=2.0031 (1/4) tap 3: pos=-17.9969 gap=2.0031 (2/4) tap 4: pos=-17.9969 gap=2.0031 (3/4) tap 5: pos=-17.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-17.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-18.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.5697 gap=1.4303 (chauffe, ignore) tap 2: pos=457.1797 gap=1.8203 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.1828/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=457.0426 spread=0.1828mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-17.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-17.9969 gap=2.0031 (1/4) tap 3: pos=-17.9969 gap=2.0031 (2/4) tap 4: pos=-17.9969 gap=2.0031 (3/4) tap 5: pos=-17.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-17.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-18.0000 Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.995,339.999 is z=407.775000 Tap OK (diff=0.0000mm, stable 2/5) probe at 49.995,339.999 is z=407.780000 Tap OK (diff=0.0050mm, stable 3/5) probe at 49.995,339.999 is z=407.777500 Tap OK (diff=0.0025mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=407.7775 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (50.0, 340.0) ~ point de tap (50.0, 340.0) Z calibration complete!

Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.998,339.999 is z=493.202500 probe at 49.998,339.999 is z=416.302500 Tap drift (diff=76.9000mm) — reset probe at 49.998,339.999 is z=418.337500 Tap drift (diff=2.0350mm) — reset probe at 49.998,339.999 is z=410.167500 Tap drift (diff=8.1700mm) — reset probe at 49.998,339.999 is z=351.727500 Tap drift (diff=58.4400mm) — reset probe at 49.998,339.999 is z=354.570000 Tap drift (diff=2.8425mm) — reset probe at 49.998,339.999 is z=311.565000 Tap drift (diff=43.0050mm) — reset probe at 49.998,339.999 is z=304.935000 Tap drift (diff=6.6300mm) — reset probe at 49.998,339.999 is z=25.250000 Tap drift (diff=279.6850mm) — reset probe at 49.998,339.999 is z=25.260000 Tap OK (diff=0.0100mm, stable 2/5) probe at 49.998,339.999 is z=25.257500 Tap OK (diff=0.0025mm, stable 3/5) probe at 49.998,339.999 is z=25.262500 Tap OK (diff=0.0050mm, stable 4/5) probe at 49.998,339.999 is z=25.265000 Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=25.2650 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (50.0, 340.0) ~ point de tap (50.0, 340.0) Z calibration complete! probe at 49.998,339.999 is z=486.097500 Tap OK (diff=0.0000mm, stable 2/5) Tap OK (diff=0.0000mm, stable 3/5) probe at 49.998,339.999 is z=486.092500 probe at 49.998,339.999 is z=486.090000 VALIDATED: trigger_z=486.0900 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) probe at 49.998,339.999 is z=486.110000 probe at 49.998,339.999 is z=486.107500 Tap OK (diff=0.0025mm, stable 2/5) probe at 49.998,339.999 is z=486.100000

probe: at 54.997,328.001 bed will contact at z=1.517500 probe: at 54.997,328.001 bed will contact at z=1.527500 probe: at 54.997,328.001 bed will contact at z=1.525000 probe: at 380.001,328.001 bed will contact at z=1.505000 probe: at 380.001,328.001 bed will contact at z=1.480000 probe: at 380.001,328.001 bed will contact at z=1.500000 probe: at 380.001,101.996 bed will contact at z=1.440000 probe: at 380.001,101.996 bed will contact at z=1.450000 probe: at 380.001,101.996 bed will contact at z=1.437500 probe: at 54.997,101.996 bed will contact at z=1.532500 probe: at 54.997,101.996 bed will contact at z=1.525000 probe: at 54.997,101.996 bed will contact at z=1.535000 probe: at 217.505,214.498 bed will contact at z=1.560000 probe: at 217.505,214.498 bed will contact at z=1.572500 probe: at 217.505,214.498 bed will contact at z=1.552500 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=72.0, y=298.0, z=1.52500 front right screw : x=397.0, y=298.0, z=1.50000 : adjust CCW 00:03 rear right screw : x=397.0, y=72.0, z=1.44000 : adjust CCW 00:10 rear left screw : x=72.0, y=72.0, z=1.53250 : adjust CW 00:01 middle : x=234.5, y=184.5, z=1.56000 : adjust CW 00:04