[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C435;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22S148H;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=110V;bedw=550;ssr=SSR10DA;lot=20260618;uid=2ACAAE [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=57006C001051353135323934

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1 rejete: cible atteinte sans buter (gap=0.0653) tap 2 rejete: cible atteinte sans buter (gap=0.0531) YUMI_SENSORLESS_HOME X: home de base suspect (pas de contact) -> re-home de recuperation 1/2 tap 3: pos=457.4112 gap=1.5888 (chauffe, ignore) tap 4: pos=456.9969 gap=2.0031 (1/4) tap 5: pos=456.9969 gap=2.0031 (2/4) tap 6: pos=456.9969 gap=2.0031 (3/4) tap 7: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (2 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.1675 gap=1.8325 (chauffe, ignore) tap 2: pos=-18.7769 gap=1.2231 (1/4) tap 3: pos=-18.7769 gap=1.2231 (2/4) tap 4: pos=-18.7769 gap=1.2231 (3/4) tap 5: pos=-18.7769 gap=1.2231 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-18.7769 spread=0.0000mm (tol=0.0500). Zero pose en butee=-18.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.8019 gap=2.1981 (3/4) tap 5: pos=457.1919 gap=1.8081 fenetre=0.3900/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.3900mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.1797 gap=1.8203 (chauffe, ignore) tap 2: pos=-18.7769 gap=1.2231 (1/4) tap 3: pos=-18.7769 gap=1.2231 (2/4) tap 4: pos=-18.7769 gap=1.2231 (3/4) tap 5: pos=-18.7769 gap=1.2231 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-18.7769 spread=0.0000mm (tol=0.0500). Zero pose en butee=-18.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 100mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.2163 gap=1.7837 (chauffe, ignore) tap 2: pos=457.1919 gap=1.8081 (1/4) tap 3: pos=456.8019 gap=2.1981 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=457.1919 gap=1.8081 fenetre=0.3900/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=457.0456 spread=0.3900mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.1797 gap=1.8203 (chauffe, ignore) tap 2: pos=-18.7769 gap=1.2231 (1/4) tap 3: pos=-18.5941 gap=1.4059 (2/4) tap 4: pos=-18.1797 gap=1.8203 (3/4) tap 5: pos=-18.7769 gap=1.2231 fenetre=0.5972/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-18.5819 spread=0.5972mm (tol=0.0500). Zero pose en butee=-18.0000 Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.995,339.999 is z=411.622500 probe at 49.995,339.999 is z=411.632500 Tap drift (diff=0.0100mm) — reset probe at 49.995,339.999 is z=411.640000 Tap OK (diff=0.0075mm, stable 2/5) Tap OK (diff=0.0000mm, stable 3/5) probe at 49.995,339.999 is z=411.642500 Tap OK (diff=0.0025mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=411.6425 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (50.0, 340.0) ~ point de tap (50.0, 340.0) Z calibration complete!

Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.998,339.999 is z=328.377500 probe at 49.998,339.999 is z=233.872500 Tap drift (diff=94.5050mm) — reset probe at 49.998,339.999 is z=232.860000 Tap drift (diff=1.0125mm) — reset probe at 49.998,339.999 is z=227.850000 Tap drift (diff=5.0100mm) — reset probe at 49.998,339.999 is z=221.152500 Tap drift (diff=6.6975mm) — reset probe at 49.998,339.999 is z=214.270000 Tap drift (diff=6.8825mm) — reset probe at 49.998,339.999 is z=208.587500 Tap drift (diff=5.6825mm) — reset probe at 49.998,339.999 is z=200.752500 Tap drift (diff=7.8350mm) — reset probe at 49.998,339.999 is z=202.405000 Tap drift (diff=1.6525mm) — reset probe at 49.998,339.999 is z=205.402500 Tap drift (diff=2.9975mm) — reset probe at 49.998,339.999 is z=207.385000 Tap drift (diff=1.9825mm) — reset probe at 49.998,339.999 is z=33.537500 Tap drift (diff=173.8475mm) — reset probe at 49.998,339.999 is z=1.072500 Tap drift (diff=32.4650mm) — reset probe at 49.998,339.999 is z=1.080000 Tap OK (diff=0.0075mm, stable 2/5) probe at 49.998,339.999 is z=1.087500 Tap OK (diff=0.0075mm, stable 3/5) probe at 49.998,339.999 is z=1.092500 Tap OK (diff=0.0050mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=1.0925 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (50.0, 340.0) ~ point de tap (50.0, 340.0) Z calibration complete! probe at 49.998,339.999 is z=492.240000 probe at 49.998,339.999 is z=486.102500 Tap drift (diff=6.1375mm) — reset

probe: at 54.997,328.001 bed will contact at z=1.787500 probe: at 54.997,328.001 bed will contact at z=1.785000 probe: at 54.997,328.001 bed will contact at z=1.792500 probe: at 380.001,328.001 bed will contact at z=1.687500 probe: at 380.001,328.001 bed will contact at z=1.695000 probe: at 380.001,101.996 bed will contact at z=1.767500 probe: at 380.001,101.996 bed will contact at z=1.772500 probe: at 54.997,101.996 bed will contact at z=1.787500 probe: at 54.997,101.996 bed will contact at z=1.802500 probe: at 54.997,101.996 bed will contact at z=1.790000 probe: at 217.505,214.498 bed will contact at z=1.842500 probe: at 217.505,214.498 bed will contact at z=1.847500 probe: at 217.505,214.498 bed will contact at z=1.830000 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=72.0, y=298.0, z=1.78750 front right screw : x=397.0, y=298.0, z=1.68750 : adjust CCW 00:12 rear right screw : x=397.0, y=72.0, z=1.76750 : adjust CCW 00:02 rear left screw : x=72.0, y=72.0, z=1.79000 : adjust CW 00:00 middle : x=234.5, y=184.5, z=1.84250 : adjust CW 00:07