[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C335;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22DH;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=500;ssr=SSR10DA;lot=20260618;uid=36C6E9 [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=58002C001051353135323934

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.7769 gap=1.2231 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.7891 gap=1.2109 (chauffe, ignore) tap 2: pos=-30.1919 gap=1.8081 (1/4) tap 3: pos=-30.7769 gap=1.2231 (2/4) tap 4: pos=-30.7769 gap=1.2231 (3/4) tap 5: pos=-30.9719 gap=1.0281 fenetre=0.7800/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-30.6794 spread=0.7800mm (tol=0.0500). Zero pose en butee=-30.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.1919 gap=1.8081 (chauffe, ignore) tap 2: pos=-30.5819 gap=1.4181 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-30.1919 gap=1.8081 fenetre=0.5850/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-30.1919 spread=0.5850mm (tol=0.0500). Zero pose en butee=-30.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.1919 gap=1.8081 (chauffe, ignore) tap 2: pos=-30.5819 gap=1.4181 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.5850/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-30.1431 spread=0.5850mm (tol=0.0500). Zero pose en butee=-30.0000 Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.996,275.995 is z=318.370000 probe at 65.996,275.995 is z=306.305000 Tap drift (diff=12.0650mm) — reset probe at 65.996,275.995 is z=306.317500 Tap drift (diff=0.0125mm) — reset probe at 65.996,275.995 is z=306.315000 Tap OK (diff=0.0025mm, stable 2/5) Tap OK (diff=0.0025mm, stable 3/5) probe at 65.996,275.995 is z=306.322500 Tap OK (diff=0.0050mm, stable 4/5) Tap OK (diff=0.0075mm, stable 5/5) VALIDATED: trigger_z=306.3150 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (66.0, 276.0) ~ point de tap (66.0, 276.0) Z calibration complete!

Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.999,275.995 is z=310.872500 probe at 65.999,275.995 is z=237.987500 Tap drift (diff=72.8850mm) — reset probe at 65.999,275.995 is z=202.547500 Tap drift (diff=35.4400mm) — reset probe at 65.999,275.995 is z=175.757500 Tap drift (diff=26.7900mm) — reset probe at 65.999,275.995 is z=178.550000 Tap drift (diff=2.7925mm) — reset probe at 65.999,275.995 is z=131.355000 Tap drift (diff=47.1950mm) — reset probe at 65.999,275.995 is z=133.820000 Tap drift (diff=2.4650mm) — reset probe at 65.999,275.995 is z=129.347500 Tap drift (diff=4.4725mm) — reset probe at 65.999,275.995 is z=132.272500 Tap drift (diff=2.9250mm) — reset probe at 65.999,275.995 is z=131.150000 Tap drift (diff=1.1225mm) — reset probe at 65.999,275.995 is z=133.942500 probe at 65.999,275.995 is z=132.860000 Tap drift (diff=1.0825mm) — reset probe at 65.999,275.995 is z=135.627500 Tap drift (diff=2.7675mm) — reset probe at 65.999,275.995 is z=134.745000 Tap drift (diff=0.8825mm) — reset probe at 65.999,275.995 is z=127.980000 Tap drift (diff=6.7650mm) — reset probe at 65.999,275.995 is z=130.762500 Tap drift (diff=2.7825mm) — reset Switch encore declenche (vibration) -> attente 2.0s puis nouvelle tentative (1/10) probe at 65.999,275.995 is z=115.512500 Tap drift (diff=15.2500mm) — reset probe at 65.999,275.995 is z=118.275000 Tap drift (diff=2.7625mm) — reset probe at 65.999,275.995 is z=42.230000 Tap drift (diff=76.0450mm) — reset probe at 65.999,275.995 is z=0.855000

probe: at 67.000,271.004 bed will contact at z=0.997500 probe: at 67.000,271.004 bed will contact at z=1.030000 probe: at 67.000,271.004 bed will contact at z=1.007500 probe: at 267.996,271.004 bed will contact at z=1.000000 probe: at 267.996,271.004 bed will contact at z=0.995000 probe: at 267.996,271.004 bed will contact at z=1.002500 probe: at 267.996,71.995 bed will contact at z=1.035000 probe: at 267.996,71.995 bed will contact at z=1.022500 probe: at 267.996,71.995 bed will contact at z=1.042500 probe: at 67.000,71.995 bed will contact at z=0.992500 probe: at 67.000,71.995 bed will contact at z=0.985000 probe: at 67.000,71.995 bed will contact at z=0.995000 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=84.0, y=241.0, z=1.00750 front right screw : x=285.0, y=241.0, z=1.00000 : adjust CCW 00:01 rear right screw : x=285.0, y=42.0, z=1.03500 : adjust CW 00:03 rear left screw : x=84.0, y=42.0, z=0.99250 : adjust CCW 00:02