[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C335;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22DH;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=500;ssr=SSR10DA;lot=20260618;uid=36C6E9 [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=580051001051353135323934

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.5819 gap=1.4181 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.5819 gap=1.4181 (chauffe, ignore) tap 2: pos=-30.7769 gap=1.2231 (1/4) tap 3: pos=-30.7769 gap=1.2231 (2/4) tap 4: pos=-30.7769 gap=1.2231 (3/4) tap 5: pos=-30.7769 gap=1.2231 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-30.7769 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.5819 gap=1.4181 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.5941 gap=1.4059 (chauffe, ignore) tap 2: pos=-30.7769 gap=1.2231 (1/4) tap 3: pos=-30.7769 gap=1.2231 (2/4) tap 4: pos=-30.7769 gap=1.2231 (3/4) tap 5: pos=-30.7769 gap=1.2231 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-30.7769 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.5819 gap=1.4181 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.996,275.995 is z=312.047500 probe at 65.996,275.995 is z=312.160000 Tap drift (diff=0.1125mm) — reset probe at 65.996,275.995 is z=312.162500 Tap OK (diff=0.0025mm, stable 2/5) probe at 65.996,275.995 is z=312.165000 Tap OK (diff=0.0025mm, stable 3/5) probe at 65.996,275.995 is z=312.182500 Tap drift (diff=0.0175mm) — reset probe at 65.996,275.995 is z=312.185000 Tap OK (diff=0.0000mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) probe at 65.996,275.995 is z=312.187500 Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=312.1875 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (66.0, 276.0) ~ point de tap (66.0, 276.0) Z calibration complete!

Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.999,275.995 is z=395.630000 probe at 65.999,275.995 is z=398.237500 Tap rejete (vibration chassis, z=398.2375 > max-z_hop) -> pas de remontee, on poursuit la descente (1) probe at 65.999,275.995 is z=0.780000 probe at 65.999,275.995 is z=0.895000 Tap drift (diff=0.1150mm) — reset probe at 65.999,275.995 is z=0.900000 Tap OK (diff=0.0050mm, stable 2/5) probe at 65.999,275.995 is z=0.902500 Tap OK (diff=0.0025mm, stable 3/5) probe at 65.999,275.995 is z=0.905000 Tap OK (diff=0.0025mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=0.9050 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (66.0, 276.0) ~ point de tap (66.0, 276.0) Z calibration complete! probe at 65.999,275.995 is z=385.830000 probe at 65.999,275.995 is z=385.900000 Tap drift (diff=0.0700mm) — reset Tap OK (diff=0.0000mm, stable 2/5) probe at 65.999,275.995 is z=385.902500 probe at 65.999,275.995 is z=385.905000 VALIDATED: trigger_z=385.9050 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) probe at 65.999,275.995 is z=385.847500 probe at 65.999,275.995 is z=385.897500 Tap drift (diff=0.0500mm) — reset Tap OK (diff=0.0025mm, stable 2/5) Tap OK (diff=0.0000mm, stable 3/5) probe at 65.999,275.995 is z=388.065000 Tap drift (diff=2.1650mm) — reset Tap drift (diff=2.1625mm) — reset probe at 65.999,275.995 is z=392.385000 probe at 65.999,275.995 is z=386.782500 Tap drift (diff=5.6025mm) — reset probe at 65.999,275.995 is z=385.887500 Tap drift (diff=0.8950mm) — reset probe at 65.999,275.995 is z=385.895000 Tap OK (diff=0.0075mm, stable 2/5)

probe: at 67.000,271.004 bed will contact at z=1.280000 probe: at 67.000,271.004 bed will contact at z=1.450000 Probe samples exceed tolerance. Retrying... probe: at 67.000,271.004 bed will contact at z=1.390000 probe: at 67.000,271.004 bed will contact at z=1.465000 probe: at 67.000,271.004 bed will contact at z=1.407500 probe: at 67.000,271.004 bed will contact at z=1.395000 probe: at 67.000,271.004 bed will contact at z=1.340000 probe: at 67.000,271.004 bed will contact at z=1.402500 probe: at 67.000,271.004 bed will contact at z=1.347500 probe: at 67.000,271.004 bed will contact at z=1.267500 probe: at 67.000,271.004 bed will contact at z=1.352500 probe: at 67.000,271.004 bed will contact at z=1.330000 probe: at 67.000,271.004 bed will contact at z=1.370000 probe: at 67.000,271.004 bed will contact at z=1.315000 probe: at 67.000,271.004 bed will contact at z=1.410000 probe: at 67.000,271.004 bed will contact at z=1.290000 probe: at 67.000,271.004 bed will contact at z=1.420000 probe: at 67.000,271.004 bed will contact at z=1.360000 probe: at 67.000,271.004 bed will contact at z=1.430000 probe: at 67.000,271.004 bed will contact at z=1.455000 probe: at 67.000,271.004 bed will contact at z=1.460000 probe: at 267.996,271.004 bed will contact at z=1.090000 probe: at 267.996,271.004 bed will contact at z=1.120000 probe: at 267.996,271.004 bed will contact at z=1.122500 probe: at 267.996,71.995 bed will contact at z=1.200000 probe: at 267.996,71.995 bed will contact at z=1.220000 probe: at 67.000,71.995 bed will contact at z=1.337500 probe: at 67.000,71.995 bed will contact at z=1.377500 probe: at 67.000,71.995 bed will contact at z=1.410000 probe: at 67.000,71.995 bed will contact at z=1.380000 probe: at 67.000,71.995 bed will contact at z=1.422500 probe: at 67.000,71.995 bed will contact at z=1.405000 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=84.0, y=241.0, z=1.45500 front right screw : x=285.0, y=241.0, z=1.12000 : adjust CCW 00:40 rear right screw : x=285.0, y=42.0, z=1.22000 : adjust CCW 00:28 rear left screw : x=84.0, y=42.0, z=1.40500 : adjust CCW 00:06