[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C435;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22S148H;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=750;ssr=SSR10DA;lot=20260618;uid=9221AF [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=590025001051353135323934

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=467.5941 gap=1.4059 (chauffe, ignore) tap 2: pos=466.8141 gap=2.1859 (1/4) tap 3: pos=466.9969 gap=2.0031 (2/4) tap 4: pos=466.9969 gap=2.0031 (3/4) tap 5: pos=466.9969 gap=2.0031 fenetre=0.1828/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=466.9512 spread=0.1828mm (tol=0.0500). Zero pose en butee=467.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-21.5941 gap=1.4059 (chauffe, ignore) tap 2: pos=-21.7769 gap=1.2231 (1/4) tap 3: pos=-21.7769 gap=1.2231 (2/4) tap 4: pos=-21.7769 gap=1.2231 (3/4) tap 5: pos=-21.7769 gap=1.2231 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-21.7769 spread=0.0000mm (tol=0.0500). Zero pose en butee=-21.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=467.2163 gap=1.7837 (chauffe, ignore) tap 2: pos=466.9969 gap=2.0031 (1/4) tap 3: pos=466.9969 gap=2.0031 (2/4) tap 4: pos=467.1919 gap=1.8081 (3/4) tap 5: pos=467.1797 gap=1.8203 fenetre=0.1950/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=467.0913 spread=0.1950mm (tol=0.0500). Zero pose en butee=467.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-21.5941 gap=1.4059 (chauffe, ignore) tap 2: pos=-21.7769 gap=1.2231 (1/4) tap 3: pos=-21.7769 gap=1.2231 (2/4) tap 4: pos=-21.7769 gap=1.2231 (3/4) tap 5: pos=-21.7769 gap=1.2231 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-21.7769 spread=0.0000mm (tol=0.0500). Zero pose en butee=-21.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 125mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=467.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=466.9969 gap=2.0031 (1/4) tap 3: pos=466.9969 gap=2.0031 (2/4) tap 4: pos=466.8019 gap=2.1981 (3/4) tap 5: pos=467.1919 gap=1.8081 fenetre=0.3900/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=466.9969 spread=0.3900mm (tol=0.0500). Zero pose en butee=467.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-21.7769 gap=1.2231 (chauffe, ignore) tap 2: pos=-20.9969 gap=2.0031 (1/4) tap 3: pos=-20.9969 gap=2.0031 (2/4) tap 4: pos=-20.9969 gap=2.0031 (3/4) tap 5: pos=-20.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-20.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-21.0000 Moving to tap point X=56.0 Y=334.0... Probing with pressure switch... probe at 55.998,334.001 is z=409.742500 probe at 55.998,334.001 is z=409.790000 Tap drift (diff=0.0475mm) — reset probe at 55.998,334.001 is z=409.792500 Tap OK (diff=0.0025mm, stable 2/5) Tap OK (diff=0.0025mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) probe at 55.998,334.001 is z=409.780000 Tap OK (diff=0.0100mm, stable 5/5) VALIDATED: trigger_z=409.7800 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (56.0, 334.0) ~ point de tap (56.0, 334.0) Z calibration complete!

Moving to tap point X=56.0 Y=334.0... Probing with pressure switch... probe at 56.001,334.001 is z=487.332500 probe at 56.001,334.001 is z=485.125000 Tap drift (diff=2.2075mm) — reset probe at 56.001,334.001 is z=487.945000 Tap drift (diff=2.8200mm) — reset probe at 56.001,334.001 is z=482.300000 Tap drift (diff=5.6450mm) — reset Switch encore declenche (vibration) -> attente 2.0s puis nouvelle tentative (1/10) probe at 56.001,334.001 is z=472.005000 Tap drift (diff=10.2950mm) — reset probe at 56.001,334.001 is z=468.807500 Tap drift (diff=3.1975mm) — reset probe at 56.001,334.001 is z=398.455000 Tap drift (diff=70.3525mm) — reset probe at 56.001,334.001 is z=391.657500 Tap drift (diff=6.7975mm) — reset probe at 56.001,334.001 is z=344.132500 Tap drift (diff=47.5250mm) — reset probe at 56.001,334.001 is z=337.107500 Tap drift (diff=7.0250mm) — reset probe at 56.001,334.001 is z=189.910000 Tap drift (diff=147.1975mm) — reset probe at 56.001,334.001 is z=192.375000 Tap drift (diff=2.4650mm) — reset probe at 56.001,334.001 is z=119.937500 Tap drift (diff=72.4375mm) — reset probe at 56.001,334.001 is z=122.170000 Tap drift (diff=2.2325mm) — reset probe at 56.001,334.001 is z=59.077500 Tap drift (diff=63.0925mm) — reset probe at 56.001,334.001 is z=59.145000 Tap drift (diff=0.0675mm) — reset probe at 56.001,334.001 is z=61.062500 Tap drift (diff=1.9175mm) — reset probe at 56.001,334.001 is z=59.147500 Tap drift (diff=1.9150mm) — reset probe at 56.001,334.001 is z=59.152500 Tap OK (diff=0.0050mm, stable 2/5)

probe: at 56.003,334.994 bed will contact at z=2.127500 probe: at 56.003,334.994 bed will contact at z=2.162500 probe: at 56.003,334.994 bed will contact at z=2.170000 probe: at 388.002,334.994 bed will contact at z=2.110000 probe: at 388.002,334.994 bed will contact at z=2.085000 probe: at 388.002,334.994 bed will contact at z=2.155000 Probe samples exceed tolerance. Retrying... probe: at 388.002,334.994 bed will contact at z=2.120000 probe: at 388.002,334.994 bed will contact at z=2.082500 probe: at 388.002,334.994 bed will contact at z=2.090000 probe: at 388.002,110.001 bed will contact at z=2.050000 probe: at 388.002,110.001 bed will contact at z=2.060000 probe: at 388.002,110.001 bed will contact at z=2.052500 probe: at 56.003,110.001 bed will contact at z=2.190000 probe: at 56.003,110.001 bed will contact at z=2.225000 probe: at 56.003,110.001 bed will contact at z=2.215000 probe: at 221.996,222.004 bed will contact at z=2.252500 probe: at 221.996,222.004 bed will contact at z=2.272500 probe: at 221.996,222.004 bed will contact at z=2.270000 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=73.0, y=305.0, z=2.16250 front right screw : x=405.0, y=305.0, z=2.09000 : adjust CCW 00:09 rear right screw : x=405.0, y=80.0, z=2.05250 : adjust CCW 00:13 rear left screw : x=73.0, y=80.0, z=2.21500 : adjust CW 00:06 rear middle screw : x=239.0, y=192.0, z=2.27000 : adjust CW 00:13