[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C335;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22DH;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=110V;bedw=500;ssr=SSR10DA;lot=20260618;uid=B3D7BD [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=590069001051353135323934

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.6062 gap=1.3938 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1 rejete: cible atteinte sans buter (gap=0.8575) tap 2: pos=-30.7769 gap=1.2231 (chauffe, ignore) tap 3: pos=-30.7769 gap=1.2231 (1/4) tap 4: pos=-30.7769 gap=1.2231 (2/4) tap 5: pos=-30.7769 gap=1.2231 (3/4) tap 6: pos=-30.7769 gap=1.2231 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (1 rejetes) -> moyenne=-30.7769 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.6062 gap=1.3938 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.3869 gap=1.6131 (chauffe, ignore) tap 2: pos=-30.3747 gap=1.6253 (1/4) tap 3: pos=-30.3991 gap=1.6009 (2/4) tap 4: pos=-30.3747 gap=1.6253 (3/4) tap 5: pos=-30.7769 gap=1.2231 fenetre=0.4022/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-30.4813 spread=0.4022mm (tol=0.0500). Zero pose en butee=-30.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 50mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.6062 gap=1.3938 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.3747 gap=1.6253 (chauffe, ignore) tap 2: pos=-30.7769 gap=1.2231 (1/4) tap 3: pos=-30.7769 gap=1.2231 (2/4) tap 4: pos=-30.7769 gap=1.2231 (3/4) tap 5: pos=-30.7769 gap=1.2231 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-30.7769 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.996,275.995 is z=307.242500 probe at 65.996,275.995 is z=307.212500 Tap drift (diff=0.0300mm) — reset Tap OK (diff=0.0000mm, stable 2/5) Tap OK (diff=0.0000mm, stable 3/5) probe at 65.996,275.995 is z=307.217500 Tap OK (diff=0.0050mm, stable 4/5) probe at 65.996,275.995 is z=307.215000 Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=307.2150 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (66.0, 276.0) ~ point de tap (66.0, 276.0) Z calibration complete!

Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.999,275.995 is z=395.990000 probe at 65.999,275.995 is z=398.687500 Tap rejete (vibration chassis, z=398.6875 > max-z_hop) -> pas de remontee, on poursuit la descente (1) probe at 65.999,275.995 is z=326.687500 probe at 65.999,275.995 is z=329.525000 Tap drift (diff=2.8375mm) — reset probe at 65.999,275.995 is z=242.050000 Tap drift (diff=87.4750mm) — reset probe at 65.999,275.995 is z=231.745000 Tap drift (diff=10.3050mm) — reset probe at 65.999,275.995 is z=130.125000 Tap drift (diff=101.6200mm) — reset probe at 65.999,275.995 is z=68.130000 Tap drift (diff=61.9950mm) — reset probe at 65.999,275.995 is z=64.167500 Tap drift (diff=3.9625mm) — reset probe at 65.999,275.995 is z=29.372500 Tap drift (diff=34.7950mm) — reset probe at 65.999,275.995 is z=29.380000 Tap OK (diff=0.0075mm, stable 2/5) probe at 65.999,275.995 is z=29.382500 Tap OK (diff=0.0025mm, stable 3/5) probe at 65.999,275.995 is z=29.387500 Tap OK (diff=0.0050mm, stable 4/5) probe at 65.999,275.995 is z=29.392500 Tap OK (diff=0.0050mm, stable 5/5) VALIDATED: trigger_z=29.3925 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (66.0, 276.0) ~ point de tap (66.0, 276.0) Z calibration complete! probe at 65.999,275.995 is z=393.205000 probe at 65.999,275.995 is z=385.932500 Tap drift (diff=7.2725mm) — reset probe at 65.999,275.995 is z=385.940000 probe at 65.999,275.995 is z=385.952500 Tap drift (diff=0.0125mm) — reset probe at 65.999,275.995 is z=385.957500 Tap OK (diff=0.0050mm, stable 2/5) probe at 65.999,275.995 is z=385.962500

probe: at 67.000,271.004 bed will contact at z=0.667500 probe: at 67.000,271.004 bed will contact at z=0.697500 probe: at 67.000,271.004 bed will contact at z=0.625000 Probe samples exceed tolerance. Retrying... probe: at 67.000,271.004 bed will contact at z=0.677500 probe: at 67.000,271.004 bed will contact at z=0.687500 probe: at 67.000,271.004 bed will contact at z=0.637500 probe: at 267.996,271.004 bed will contact at z=0.367500 probe: at 267.996,271.004 bed will contact at z=0.357500 probe: at 267.996,271.004 bed will contact at z=0.355000 probe: at 267.996,71.995 bed will contact at z=0.357500 probe: at 267.996,71.995 bed will contact at z=0.360000 probe: at 67.000,71.995 bed will contact at z=0.322500 probe: at 67.000,71.995 bed will contact at z=0.295000 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=84.0, y=241.0, z=0.67750 front right screw : x=285.0, y=241.0, z=0.35750 : adjust CCW 00:38 rear right screw : x=285.0, y=42.0, z=0.35750 : adjust CCW 00:38 rear left screw : x=84.0, y=42.0, z=0.29500 : adjust CCW 00:46