[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C435;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22S148H;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=750;ssr=SSR10DA;lot=20260618;uid=9221AF [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=5A002C001051353135323934

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.5941 gap=1.4059 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.6062 gap=1.3938 (chauffe, ignore) tap 2: pos=-18.7647 gap=1.2353 (1/4) tap 3: pos=-18.7769 gap=1.2231 (2/4) tap 4: pos=-18.7769 gap=1.2231 (3/4) tap 5: pos=-18.7769 gap=1.2231 fenetre=0.0122/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-18.7738 spread=0.0122mm (tol=0.0500). Zero pose en butee=-18.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.5941 gap=1.4059 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=-17.9969 gap=2.0031 (1/4) tap 3: pos=-17.9969 gap=2.0031 (2/4) tap 4: pos=-17.9969 gap=2.0031 (3/4) tap 5: pos=-17.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-17.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-18.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.5819 gap=1.4181 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=-17.9969 gap=2.0031 (1/4) tap 3: pos=-17.9969 gap=2.0031 (2/4) tap 4: pos=-17.9969 gap=2.0031 (3/4) tap 5: pos=-17.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-17.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-18.0000 Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.995,339.999 is z=412.325000 probe at 49.995,339.999 is z=412.330000 Tap OK (diff=0.0050mm, stable 2/5) probe at 49.995,339.999 is z=412.332500 Tap OK (diff=0.0025mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=412.3325 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (50.0, 340.0) ~ point de tap (50.0, 340.0) Z calibration complete!

Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.998,339.999 is z=347.607500 probe at 49.998,339.999 is z=265.410000 Tap drift (diff=82.1975mm) — reset probe at 49.998,339.999 is z=267.107500 Tap drift (diff=1.6975mm) — reset probe at 49.998,339.999 is z=186.097500 Tap drift (diff=81.0100mm) — reset probe at 49.998,339.999 is z=189.002500 Tap drift (diff=2.9050mm) — reset probe at 49.998,339.999 is z=143.057500 Tap drift (diff=45.9450mm) — reset probe at 49.998,339.999 is z=136.932500 Tap drift (diff=6.1250mm) — reset probe at 49.998,339.999 is z=75.652500 Tap drift (diff=61.2800mm) — reset probe at 49.998,339.999 is z=1.082500 Tap drift (diff=74.5700mm) — reset probe at 49.998,339.999 is z=2.670000 Tap drift (diff=1.5875mm) — reset probe at 49.998,339.999 is z=1.100000 Tap drift (diff=1.5700mm) — reset probe at 49.998,339.999 is z=1.102500 Tap OK (diff=0.0025mm, stable 2/5) probe at 49.998,339.999 is z=1.107500 Tap OK (diff=0.0050mm, stable 3/5) probe at 49.998,339.999 is z=1.105000 Tap OK (diff=0.0025mm, stable 4/5) Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=1.1075 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (50.0, 340.0) ~ point de tap (50.0, 340.0) Z calibration complete! probe at 49.998,339.999 is z=486.127500 probe at 49.998,339.999 is z=489.060000 Tap drift (diff=2.9325mm) — reset probe at 49.998,339.999 is z=486.100000 Tap drift (diff=2.9600mm) — reset probe at 49.998,339.999 is z=486.095000 Tap OK (diff=0.0050mm, stable 2/5)

probe: at 54.997,328.001 bed will contact at z=1.790000 probe: at 54.997,328.001 bed will contact at z=1.787500 probe: at 54.997,328.001 bed will contact at z=1.785000 probe: at 380.001,328.001 bed will contact at z=1.900000 probe: at 380.001,328.001 bed will contact at z=1.807500 Probe samples exceed tolerance. Retrying... probe: at 380.001,328.001 bed will contact at z=1.865000 probe: at 380.001,328.001 bed will contact at z=1.845000 probe: at 380.001,328.001 bed will contact at z=1.835000 probe: at 380.001,101.996 bed will contact at z=1.737500 probe: at 380.001,101.996 bed will contact at z=1.837500 probe: at 380.001,101.996 bed will contact at z=1.752500 probe: at 380.001,101.996 bed will contact at z=1.795000 probe: at 380.001,101.996 bed will contact at z=1.810000 probe: at 380.001,101.996 bed will contact at z=1.815000 probe: at 380.001,101.996 bed will contact at z=1.785000 probe: at 380.001,101.996 bed will contact at z=1.732500 probe: at 380.001,101.996 bed will contact at z=1.722500 probe: at 380.001,101.996 bed will contact at z=1.727500 probe: at 380.001,101.996 bed will contact at z=1.677500 probe: at 54.997,101.996 bed will contact at z=1.710000 probe: at 54.997,101.996 bed will contact at z=1.727500 probe: at 217.505,214.498 bed will contact at z=1.770000 probe: at 217.505,214.498 bed will contact at z=1.765000 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=72.0, y=298.0, z=1.78750 front right screw : x=397.0, y=298.0, z=1.84500 : adjust CW 00:07 rear right screw : x=397.0, y=72.0, z=1.72250 : adjust CCW 00:08 rear left screw : x=72.0, y=72.0, z=1.72750 : adjust CCW 00:07 middle : x=234.5, y=184.5, z=1.77000 : adjust CCW 00:02