[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C335;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22DH;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=500;ssr=SSR10DA;lot=20260618;uid=36C6E9 [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=5B0044000D51353234323830

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.0091 gap=1.9909 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-29.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 50mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.4234 gap=1.5766 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-29.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.996,275.995 is z=315.687500 probe at 65.996,275.995 is z=315.737500 Tap drift (diff=0.0500mm) — reset probe at 65.996,275.995 is z=315.765000 Tap drift (diff=0.0275mm) — reset probe at 65.996,275.995 is z=315.795000 Tap drift (diff=0.0300mm) — reset probe at 65.996,275.995 is z=315.807500 Tap drift (diff=0.0125mm) — reset probe at 65.996,275.995 is z=315.832500 Tap drift (diff=0.0250mm) — reset probe at 65.996,275.995 is z=315.845000 probe at 65.996,275.995 is z=315.852500 Tap OK (diff=0.0075mm, stable 2/5) probe at 65.996,275.995 is z=315.877500 probe at 65.996,275.995 is z=315.885000 probe at 65.996,275.995 is z=315.887500 Tap OK (diff=0.0025mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=315.8875 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000)

Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.999,275.995 is z=0.655000 probe at 65.999,275.995 is z=0.702500 Tap drift (diff=0.0475mm) — reset probe at 65.999,275.995 is z=0.737500 Tap drift (diff=0.0350mm) — reset probe at 65.999,275.995 is z=0.770000 Tap drift (diff=0.0325mm) — reset probe at 65.999,275.995 is z=0.782500 Tap drift (diff=0.0125mm) — reset probe at 65.999,275.995 is z=0.807500 Tap drift (diff=0.0250mm) — reset probe at 65.999,275.995 is z=0.817500 Tap drift (diff=0.0100mm) — reset probe at 65.999,275.995 is z=0.827500 probe at 65.999,275.995 is z=0.850000 Tap drift (diff=0.0225mm) — reset probe at 65.999,275.995 is z=0.857500 Tap OK (diff=0.0075mm, stable 2/5) probe at 65.999,275.995 is z=0.865000 Tap OK (diff=0.0075mm, stable 3/5) probe at 65.999,275.995 is z=0.882500 Tap drift (diff=0.0175mm) — reset probe at 65.999,275.995 is z=0.892500 probe at 65.999,275.995 is z=0.895000 Tap OK (diff=0.0025mm, stable 2/5) probe at 65.999,275.995 is z=0.897500 Tap OK (diff=0.0025mm, stable 3/5) probe at 65.999,275.995 is z=0.900000 Tap OK (diff=0.0025mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=0.9000 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (66.0, 276.0) ~ point de tap (66.0, 276.0) Z calibration complete! probe at 65.999,275.995 is z=385.895000 probe at 65.999,275.995 is z=385.897500 probe at 65.999,275.995 is z=385.900000 Tap OK (diff=0.0000mm, stable 4/5) VALIDATED: trigger_z=385.9000 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000)

probe: at 67.000,271.004 bed will contact at z=1.510000 probe: at 67.000,271.004 bed will contact at z=1.525000 probe: at 67.000,271.004 bed will contact at z=1.515000 probe: at 267.996,271.004 bed will contact at z=1.395000 probe: at 267.996,271.004 bed will contact at z=1.400000 probe: at 267.996,71.995 bed will contact at z=1.352500 probe: at 267.996,71.995 bed will contact at z=1.355000 probe: at 267.996,71.995 bed will contact at z=1.362500 probe: at 67.000,71.995 bed will contact at z=0.937500 probe: at 67.000,71.995 bed will contact at z=1.105000 Probe samples exceed tolerance. Retrying... probe: at 67.000,71.995 bed will contact at z=1.097500 probe: at 67.000,71.995 bed will contact at z=1.117500 probe: at 67.000,71.995 bed will contact at z=1.140000 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=84.0, y=241.0, z=1.51500 front right screw : x=285.0, y=241.0, z=1.39500 : adjust CCW 00:14 rear right screw : x=285.0, y=42.0, z=1.35500 : adjust CCW 00:19 rear left screw : x=84.0, y=42.0, z=1.11750 : adjust CCW 00:48