[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C235;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22DH;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=300;ssr=SSR10DA;lot=20260616;uid=61C229 [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=5C0044000D51353234323830

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=256.1919 gap=1.8081 (1/4) tap 3: pos=255.9969 gap=2.0031 (2/4) tap 4: pos=255.9969 gap=2.0031 (3/4) tap 5: pos=255.9969 gap=2.0031 fenetre=0.1950/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=256.0456 spread=0.1950mm (tol=0.0500). Zero pose en butee=256.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.3991 gap=1.6009 (chauffe, ignore) tap 2: pos=-29.8019 gap=2.1981 (1/4) tap 3: pos=-30.1919 gap=1.8081 (2/4) tap 4: pos=-29.8019 gap=2.1981 (3/4) tap 5: pos=-30.1919 gap=1.8081 fenetre=0.3900/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.3900mm (tol=0.0500). Zero pose en butee=-30.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.6062 gap=1.3938 (chauffe, ignore) tap 2: pos=255.8019 gap=2.1981 (1/4) tap 3: pos=256.1919 gap=1.8081 (2/4) tap 4: pos=255.9969 gap=2.0031 (3/4) tap 5: pos=255.9969 gap=2.0031 fenetre=0.3900/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=255.9969 spread=0.3900mm (tol=0.0500). Zero pose en butee=256.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.1919 gap=1.8081 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-30.1919 gap=1.8081 (3/4) tap 5: pos=-29.8019 gap=2.1981 fenetre=0.3900/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.3900mm (tol=0.0500). Zero pose en butee=-30.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 50mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=255.9969 gap=2.0031 (1/4) tap 3: pos=255.9969 gap=2.0031 (2/4) tap 4: pos=256.1919 gap=1.8081 (3/4) tap 5: pos=255.8019 gap=2.1981 fenetre=0.3900/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=255.9969 spread=0.3900mm (tol=0.0500). Zero pose en butee=256.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.1919 gap=1.8081 (chauffe, ignore) tap 2: pos=-29.8019 gap=2.1981 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-30.1919 gap=1.8081 fenetre=0.3900/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.3900mm (tol=0.0500). Zero pose en butee=-30.0000 Moving to tap point X=31.0 Y=212.0... Probing with pressure switch... probe at 31.003,211.998 is z=265.445000 probe at 31.003,211.998 is z=155.770000 Tap drift (diff=109.6750mm) — reset probe at 31.003,211.998 is z=155.942500 Tap drift (diff=0.1725mm) — reset probe at 31.003,211.998 is z=155.962500 Tap drift (diff=0.0200mm) — reset probe at 31.003,211.998 is z=155.967500 Tap OK (diff=0.0050mm, stable 2/5) probe at 31.003,211.998 is z=155.965000 Tap OK (diff=0.0025mm, stable 3/5) probe at 31.003,211.998 is z=155.970000 Tap OK (diff=0.0050mm, stable 4/5) probe at 31.003,211.998 is z=155.972500 Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=155.9725 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (31.0, 212.0) ~ point de tap (31.0, 212.0) Z calibration complete!

Moving to tap point X=31.0 Y=212.0... Probing with pressure switch... probe at 30.994,211.998 is z=0.620000 probe at 30.994,211.998 is z=0.817500 Tap drift (diff=0.1975mm) — reset probe at 30.994,211.998 is z=0.820000 Tap OK (diff=0.0025mm, stable 2/5) Tap OK (diff=0.0025mm, stable 3/5) Tap OK (diff=0.0025mm, stable 4/5) probe at 30.994,211.998 is z=3.627500 Tap drift (diff=2.8075mm) — reset probe at 30.994,211.998 is z=6.305000 Tap drift (diff=2.6775mm) — reset probe at 30.994,211.998 is z=0.782500 Tap drift (diff=5.5225mm) — reset probe at 30.994,211.998 is z=0.827500 Tap drift (diff=0.0450mm) — reset probe at 30.994,211.998 is z=0.830000 Tap OK (diff=0.0000mm, stable 3/5) probe at 30.994,211.998 is z=3.630000 Tap drift (diff=2.8000mm) — reset Tap drift (diff=2.8125mm) — reset probe at 30.994,211.998 is z=0.832500 Tap drift (diff=0.0150mm) — reset probe at 30.994,211.998 is z=3.632500 probe at 30.994,211.998 is z=0.812500 Tap drift (diff=2.8200mm) — reset probe at 30.994,211.998 is z=0.857500 probe at 30.994,211.998 is z=1.980000 Tap drift (diff=1.1225mm) — reset probe at 30.994,211.998 is z=0.835000 Tap drift (diff=1.1450mm) — reset probe at 30.994,211.998 is z=0.852500 Tap drift (diff=0.0175mm) — reset probe at 30.994,211.998 is z=2.282500 Tap drift (diff=1.4300mm) — reset Tap drift (diff=1.4500mm) — reset probe at 30.994,211.998 is z=0.862500 Tap drift (diff=0.0300mm) — reset Tap OK (diff=0.0000mm, stable 2/5)

probe: at 32.495,205.497 bed will contact at z=1.465000 probe: at 32.495,205.497 bed will contact at z=1.475000 probe: at 32.495,205.497 bed will contact at z=1.537500 Probe samples exceed tolerance. Retrying... probe: at 32.495,205.497 bed will contact at z=1.440000 probe: at 32.495,205.497 bed will contact at z=1.515000 probe: at 32.495,205.497 bed will contact at z=1.485000 probe: at 32.495,205.497 bed will contact at z=1.550000 probe: at 32.495,205.497 bed will contact at z=1.455000 probe: at 32.495,205.497 bed will contact at z=1.412500 probe: at 32.495,205.497 bed will contact at z=1.535000 probe: at 32.495,205.497 bed will contact at z=1.472500 probe: at 32.495,205.497 bed will contact at z=1.542500 probe: at 32.495,205.497 bed will contact at z=1.530000 probe: at 32.495,205.497 bed will contact at z=1.522500 probe: at 32.495,205.497 bed will contact at z=1.520000 probe: at 206.996,205.497 bed will contact at z=4.222500 probe: at 206.996,205.497 bed will contact at z=4.255000 probe: at 206.996,205.497 bed will contact at z=4.252500 probe: at 206.996,31.995 bed will contact at z=3.975000 probe: at 206.996,31.995 bed will contact at z=4.007500 probe: at 206.996,31.995 bed will contact at z=4.005000 probe: at 32.495,31.995 bed will contact at z=1.657500 probe: at 32.495,31.995 bed will contact at z=1.780000 probe: at 32.495,31.995 bed will contact at z=1.790000 probe: at 32.495,31.995 bed will contact at z=1.722500 probe: at 32.495,31.995 bed will contact at z=1.737500 probe: at 32.495,31.995 bed will contact at z=1.740000 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=49.5, y=175.5, z=1.52250 front right screw : x=224.0, y=175.5, z=4.25250 : adjust CW 05:28 rear right screw : x=224.0, y=2.0, z=4.00500 : adjust CW 04:58 rear left screw : x=49.5, y=2.0, z=1.73750 : adjust CW 00:26