[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C335;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22DH;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=500;ssr=SSR10DA;lot=20260618;uid=36C6E9 [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=5D0051000C51353234323830

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.2041 gap=1.7959 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.7769 gap=1.2231 (chauffe, ignore) tap 2: pos=-30.1919 gap=1.8081 (1/4) tap 3: pos=-30.5819 gap=1.4181 (2/4) tap 4: pos=-30.1919 gap=1.8081 (3/4) tap 5: pos=-30.5819 gap=1.4181 fenetre=0.3900/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-30.3869 spread=0.3900mm (tol=0.0500). Zero pose en butee=-30.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.7769 gap=1.2231 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-29.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-30.1919 gap=1.8081 (1/4) tap 3: pos=-30.5819 gap=1.4181 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-30.1919 gap=1.8081 fenetre=0.5850/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-30.2406 spread=0.5850mm (tol=0.0500). Zero pose en butee=-30.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 100mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-29.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-30.1919 gap=1.8081 (2/4) tap 4: pos=-30.5819 gap=1.4181 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.5850/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-30.1919 spread=0.5850mm (tol=0.0500). Zero pose en butee=-30.0000 Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.996,275.995 is z=285.655000 probe at 65.996,275.995 is z=285.465000 Tap drift (diff=0.1900mm) — reset probe at 65.996,275.995 is z=285.292500 Tap drift (diff=0.1725mm) — reset probe at 65.996,275.995 is z=285.130000 Tap drift (diff=0.1625mm) — reset probe at 65.996,275.995 is z=284.972500 Tap drift (diff=0.1575mm) — reset probe at 65.996,275.995 is z=284.810000 probe at 65.996,275.995 is z=284.652500 probe at 65.996,275.995 is z=287.152500 Tap drift (diff=2.5000mm) — reset probe at 65.996,275.995 is z=287.357500 Tap drift (diff=0.2050mm) — reset probe at 65.996,275.995 is z=287.360000 Tap OK (diff=0.0025mm, stable 2/5) probe at 65.996,275.995 is z=287.362500 Tap OK (diff=0.0025mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) Tap OK (diff=0.0050mm, stable 5/5)

Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.999,275.995 is z=327.375000 probe at 65.999,275.995 is z=193.657500 Tap drift (diff=133.7175mm) — reset probe at 65.999,275.995 is z=188.695000 Tap drift (diff=4.9625mm) — reset probe at 65.999,275.995 is z=191.097500 Tap drift (diff=2.4025mm) — reset probe at 65.999,275.995 is z=193.495000 Tap drift (diff=2.3975mm) — reset probe at 65.999,275.995 is z=195.257500 Tap drift (diff=1.7625mm) — reset probe at 65.999,275.995 is z=196.215000 Tap drift (diff=0.9575mm) — reset probe at 65.999,275.995 is z=198.932500 Tap drift (diff=2.7175mm) — reset probe at 65.999,275.995 is z=201.335000 probe at 65.999,275.995 is z=200.612500 Tap drift (diff=0.7225mm) — reset probe at 65.999,275.995 is z=200.052500 Tap drift (diff=0.5600mm) — reset probe at 65.999,275.995 is z=201.172500 Tap drift (diff=1.1200mm) — reset probe at 65.999,275.995 is z=201.650000 Tap drift (diff=0.4775mm) — reset probe at 65.999,275.995 is z=195.942500 Tap drift (diff=5.7075mm) — reset probe at 65.999,275.995 is z=193.095000 Tap drift (diff=2.8475mm) — reset probe at 65.999,275.995 is z=-1.450000 Tap drift (diff=194.5450mm) — reset probe at 65.999,275.995 is z=1.097500 Tap drift (diff=2.5475mm) — reset probe at 65.999,275.995 is z=1.107500 Tap drift (diff=0.0100mm) — reset Tap OK (diff=0.0000mm, stable 2/5) probe at 65.999,275.995 is z=1.102500 Tap OK (diff=0.0050mm, stable 3/5) probe at 65.999,275.995 is z=1.100000

probe: at 67.000,271.004 bed will contact at z=2.025000 probe: at 67.000,271.004 bed will contact at z=2.032500 probe: at 67.000,271.004 bed will contact at z=2.052500 probe: at 267.996,271.004 bed will contact at z=2.050000 probe: at 267.996,271.004 bed will contact at z=2.052500 probe: at 267.996,271.004 bed will contact at z=2.055000 probe: at 267.996,71.995 bed will contact at z=2.010000 probe: at 267.996,71.995 bed will contact at z=2.015000 probe: at 67.000,71.995 bed will contact at z=2.007500 probe: at 67.000,71.995 bed will contact at z=2.005000 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=84.0, y=241.0, z=2.03250 front right screw : x=285.0, y=241.0, z=2.05250 : adjust CW 00:02 rear right screw : x=285.0, y=42.0, z=2.01000 : adjust CCW 00:03 rear left screw : x=84.0, y=42.0, z=2.00750 : adjust CCW 00:03