[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C435;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22S148H;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=750;ssr=SSR10DA;lot=20260618;uid=9221AF [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=5D005C000C51353234323830

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1 rejete: aucun contact sur 7.0mm (No trigger on probe after full movement) tap 2: pos=-18.9353 gap=1.0647 (chauffe, ignore) tap 3: pos=-17.9969 gap=2.0031 (1/4) tap 4: pos=-17.9969 gap=2.0031 (2/4) tap 5: pos=-18.1797 gap=1.8203 (3/4) tap 6: pos=-17.9969 gap=2.0031 fenetre=0.1828/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (1 rejetes) -> moyenne=-18.0426 spread=0.1828mm (tol=0.0500). Zero pose en butee=-18.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.7769 gap=1.2231 (chauffe, ignore) tap 2: pos=-18.1797 gap=1.8203 (1/4) tap 3: pos=-17.9969 gap=2.0031 (2/4) tap 4: pos=-17.9969 gap=2.0031 (3/4) tap 5: pos=-17.9969 gap=2.0031 fenetre=0.1828/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-18.0426 spread=0.1828mm (tol=0.0500). Zero pose en butee=-18.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.7769 gap=1.2231 (chauffe, ignore) tap 2: pos=-17.9969 gap=2.0031 (1/4) tap 3: pos=-17.9969 gap=2.0031 (2/4) tap 4: pos=-17.9969 gap=2.0031 (3/4) tap 5: pos=-17.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-17.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-18.0000 Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.995,339.999 is z=485.907500 probe at 49.995,339.999 is z=405.920000 Tap drift (diff=79.9875mm) — reset probe at 49.995,339.999 is z=405.912500 Tap OK (diff=0.0075mm, stable 2/5) probe at 49.995,339.999 is z=405.887500 Tap drift (diff=0.0250mm) — reset probe at 49.995,339.999 is z=405.880000 probe at 49.995,339.999 is z=405.875000 Tap OK (diff=0.0050mm, stable 3/5) probe at 49.995,339.999 is z=405.870000 Tap OK (diff=0.0050mm, stable 4/5) probe at 49.995,339.999 is z=405.862500 Tap OK (diff=0.0075mm, stable 5/5) VALIDATED: trigger_z=405.8625 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (50.0, 340.0) ~ point de tap (50.0, 340.0) Z calibration complete!

Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.998,339.999 is z=1.157500 probe at 49.998,339.999 is z=3.877500 Tap drift (diff=2.7200mm) — reset probe at 49.998,339.999 is z=1.160000 Tap drift (diff=2.7175mm) — reset Tap OK (diff=0.0000mm, stable 2/5) Tap OK (diff=0.0000mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=1.1575 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (50.0, 340.0) ~ point de tap (50.0, 340.0) Z calibration complete! probe at 49.998,339.999 is z=486.105000 probe at 49.998,339.999 is z=487.785000 Tap drift (diff=1.6800mm) — reset probe at 49.998,339.999 is z=489.100000 Tap drift (diff=2.9950mm) — reset probe at 49.998,339.999 is z=489.817500 Tap drift (diff=0.7175mm) — reset Tap drift (diff=3.7125mm) — reset probe at 49.998,339.999 is z=486.102500 Tap OK (diff=0.0025mm, stable 2/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=486.1025 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) probe at 49.998,339.999 is z=486.100000 Tap OK (diff=0.0025mm, stable 3/5) VALIDATED: trigger_z=486.1000 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) probe at 49.998,339.999 is z=495.782500 Switch encore declenche (vibration) -> attente 2.0s puis nouvelle tentative (1/10) probe at 49.998,339.999 is z=498.492500 Tap rejete (vibration chassis, z=498.4925 > max-z_hop) -> pas de remontee, on poursuit la descente (1) VALIDATED: trigger_z=486.1050 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) probe at 49.998,339.999 is z=493.810000 probe at 49.998,339.999 is z=486.097500 Tap drift (diff=7.7125mm) — reset Tap OK (diff=0.0025mm, stable 4/5) VALIDATED: trigger_z=486.0975 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) probe at 49.998,339.999 is z=486.095000

probe: at 54.997,328.001 bed will contact at z=1.567500 probe: at 54.997,328.001 bed will contact at z=1.580000 probe: at 380.001,328.001 bed will contact at z=1.580000 probe: at 380.001,328.001 bed will contact at z=1.562500 probe: at 380.001,101.996 bed will contact at z=1.515000 probe: at 380.001,101.996 bed will contact at z=1.527500 probe: at 380.001,101.996 bed will contact at z=1.525000 probe: at 54.997,101.996 bed will contact at z=1.507500 probe: at 54.997,101.996 bed will contact at z=1.510000 probe: at 54.997,101.996 bed will contact at z=1.500000 probe: at 217.505,214.498 bed will contact at z=1.630000 probe: at 217.505,214.498 bed will contact at z=1.572500 Probe samples exceed tolerance. Retrying... probe: at 217.505,214.498 bed will contact at z=1.575000 probe: at 217.505,214.498 bed will contact at z=1.612500 probe: at 217.505,214.498 bed will contact at z=1.647500 probe: at 217.505,214.498 bed will contact at z=1.595000 probe: at 217.505,214.498 bed will contact at z=1.582500 probe: at 217.505,214.498 bed will contact at z=1.655000 probe: at 217.505,214.498 bed will contact at z=1.685000 probe: at 217.505,214.498 bed will contact at z=1.567500 probe: at 217.505,214.498 bed will contact at z=1.642500 probe: at 217.505,214.498 bed will contact at z=1.547500 probe: at 217.505,214.498 bed will contact at z=1.600000 probe: at 217.505,214.498 bed will contact at z=1.627500 probe: at 217.505,214.498 bed will contact at z=1.620000 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=72.0, y=298.0, z=1.58000 front right screw : x=397.0, y=298.0, z=1.58000 : adjust CCW 00:00 rear right screw : x=397.0, y=72.0, z=1.52500 : adjust CCW 00:07 rear left screw : x=72.0, y=72.0, z=1.50750 : adjust CCW 00:09 middle : x=234.5, y=184.5, z=1.62000 : adjust CW 00:05