[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C235;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22DH;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=300;ssr=SSR10DA;lot=20260616;uid=61C229 [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=5E0050000C51353234323830

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=255.9969 gap=2.0031 (1/4) tap 3: pos=255.9969 gap=2.0031 (2/4) tap 4: pos=255.9969 gap=2.0031 (3/4) tap 5: pos=255.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=255.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=256.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.1919 gap=1.8081 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=255.9969 gap=2.0031 (1/4) tap 3: pos=255.9969 gap=2.0031 (2/4) tap 4: pos=255.9969 gap=2.0031 (3/4) tap 5: pos=255.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=255.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=256.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.1919 gap=1.8081 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 250mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=255.9969 gap=2.0031 (1/4) tap 3: pos=255.9969 gap=2.0031 (2/4) tap 4: pos=255.9969 gap=2.0031 (3/4) tap 5: pos=255.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=255.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=256.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.1797 gap=1.8203 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Moving to tap point X=31.0 Y=212.0... Probing with pressure switch... probe at 31.003,211.998 is z=175.857500 probe at 31.003,211.998 is z=175.860000 Tap OK (diff=0.0025mm, stable 2/5) probe at 31.003,211.998 is z=175.862500 Tap OK (diff=0.0025mm, stable 3/5) probe at 31.003,211.998 is z=178.857500 Tap drift (diff=2.9950mm) — reset probe at 31.003,211.998 is z=175.867500 Tap OK (diff=0.0050mm, stable 2/5) probe at 31.003,211.998 is z=175.870000 probe at 31.003,211.998 is z=175.882500 Tap drift (diff=0.0125mm) — reset Tap OK (diff=0.0000mm, stable 2/5) probe at 31.003,211.998 is z=175.887500 Tap OK (diff=0.0050mm, stable 3/5) probe at 31.003,211.998 is z=175.880000 Tap OK (diff=0.0075mm, stable 4/5) probe at 31.003,211.998 is z=175.885000 Tap OK (diff=0.0050mm, stable 5/5) VALIDATED: trigger_z=175.8850 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (31.0, 212.0) ~ point de tap (31.0, 212.0)

Moving to tap point X=31.0 Y=212.0... Probing with pressure switch... probe at 30.994,211.998 is z=195.220000 probe at 30.994,211.998 is z=180.035000 Tap drift (diff=15.1850mm) — reset probe at 30.994,211.998 is z=111.872500 Tap drift (diff=68.1625mm) — reset probe at 30.994,211.998 is z=113.510000 Tap drift (diff=1.6375mm) — reset probe at 30.994,211.998 is z=10.190000 Tap drift (diff=103.3200mm) — reset probe at 30.994,211.998 is z=0.837500 Tap drift (diff=9.3525mm) — reset probe at 30.994,211.998 is z=0.850000 Tap drift (diff=0.0125mm) — reset probe at 30.994,211.998 is z=0.870000 Tap drift (diff=0.0200mm) — reset Tap OK (diff=0.0000mm, stable 2/5) Tap OK (diff=0.0000mm, stable 3/5) probe at 30.994,211.998 is z=0.877500 Tap OK (diff=0.0075mm, stable 4/5) probe at 30.994,211.998 is z=0.880000 Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=0.8800 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (31.0, 212.0) ~ point de tap (31.0, 212.0) Z calibration complete! probe at 30.994,211.998 is z=255.895000 probe at 30.994,211.998 is z=255.922500 Tap drift (diff=0.0275mm) — reset probe at 30.994,211.998 is z=255.935000 probe at 30.994,211.998 is z=255.925000 Tap OK (diff=0.0100mm, stable 2/5) probe at 30.994,211.998 is z=255.932500 Tap OK (diff=0.0075mm, stable 3/5) probe at 30.994,211.998 is z=255.927500 Tap OK (diff=0.0050mm, stable 4/5) probe at 30.994,211.998 is z=255.937500 Tap drift (diff=0.0100mm) — reset probe at 30.994,211.998 is z=256.140000 Tap drift (diff=0.2025mm) — reset

probe: at 32.495,205.497 bed will contact at z=1.845000 probe: at 32.495,205.497 bed will contact at z=2.087500 Probe samples exceed tolerance. Retrying... probe: at 32.495,205.497 bed will contact at z=2.085000 probe: at 32.495,205.497 bed will contact at z=2.077500 probe: at 206.996,205.497 bed will contact at z=3.110000 probe: at 206.996,205.497 bed will contact at z=3.317500 probe: at 206.996,205.497 bed will contact at z=3.320000 probe: at 206.996,205.497 bed will contact at z=3.312500 probe: at 206.996,31.995 bed will contact at z=3.972500 probe: at 206.996,31.995 bed will contact at z=4.200000 probe: at 206.996,31.995 bed will contact at z=4.202500 probe: at 206.996,31.995 bed will contact at z=4.205000 probe: at 206.996,31.995 bed will contact at z=4.182500 probe: at 32.495,31.995 bed will contact at z=3.292500 probe: at 32.495,31.995 bed will contact at z=3.490000 probe: at 32.495,31.995 bed will contact at z=3.487500 probe: at 32.495,31.995 bed will contact at z=3.492500 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=49.5, y=175.5, z=2.08500 front right screw : x=224.0, y=175.5, z=3.32000 : adjust CW 02:28 rear right screw : x=224.0, y=2.0, z=4.20250 : adjust CW 04:14 rear left screw : x=49.5, y=2.0, z=3.49000 : adjust CW 02:49