[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C335;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22DH;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=500;ssr=SSR10DA;lot=20260618;uid=36C6E9 [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=60005F000C51353234323830

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=357.1797 gap=1.8203 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.1828/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=357.0426 spread=0.1828mm (tol=0.0500). Zero pose en butee=357.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.7769 gap=1.2231 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9847 gap=2.0153 (3/4) tap 5: pos=-30.0091 gap=1.9909 fenetre=0.0244/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0244mm (tol=0.0500). Zero pose en butee=-30.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.5941 gap=1.4059 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-29.9847 gap=2.0153 (chauffe, ignore) tap 2: pos=-30.0091 gap=1.9909 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9847 gap=2.0153 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0244/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0244mm (tol=0.0500). Zero pose en butee=-30.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.5941 gap=1.4059 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-29.9847 gap=2.0153 (chauffe, ignore) tap 2: pos=-30.0091 gap=1.9909 (1/4) tap 3: pos=-29.9847 gap=2.0153 (2/4) tap 4: pos=-30.0091 gap=1.9909 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0244/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9999 spread=0.0244mm (tol=0.0500). Zero pose en butee=-30.0000 Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.996,275.995 is z=307.857500 probe at 65.996,275.995 is z=310.647500 Tap drift (diff=2.7900mm) — reset probe at 65.996,275.995 is z=307.900000 Tap drift (diff=2.7475mm) — reset probe at 65.996,275.995 is z=310.690000 probe at 65.996,275.995 is z=307.922500 Tap drift (diff=2.7675mm) — reset Tap OK (diff=0.0000mm, stable 2/5) probe at 65.996,275.995 is z=307.925000 Tap OK (diff=0.0025mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) probe at 65.996,275.995 is z=307.917500 Tap OK (diff=0.0075mm, stable 5/5) VALIDATED: trigger_z=307.9175 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (66.0, 276.0) ~ point de tap (66.0, 276.0) Z calibration complete!

Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.999,275.995 is z=395.817500 probe at 65.999,275.995 is z=398.640000 Tap rejete (vibration chassis, z=398.6400 > max-z_hop) -> pas de remontee, on poursuit la descente (1) probe at 65.999,275.995 is z=398.177500 Tap rejete (vibration chassis, z=398.1775 > max-z_hop) -> pas de remontee, on poursuit la descente (2) probe at 65.999,275.995 is z=311.425000 probe at 65.999,275.995 is z=9.510000 Tap drift (diff=301.9150mm) — reset probe at 65.999,275.995 is z=12.270000 Tap drift (diff=2.7600mm) — reset probe at 65.999,275.995 is z=14.752500 Tap drift (diff=2.4825mm) — reset probe at 65.999,275.995 is z=15.712500 Tap drift (diff=0.9600mm) — reset probe at 65.999,275.995 is z=0.875000 Tap drift (diff=14.8375mm) — reset probe at 65.999,275.995 is z=3.672500 Tap drift (diff=2.7975mm) — reset probe at 65.999,275.995 is z=5.660000 Tap drift (diff=1.9875mm) — reset probe at 65.999,275.995 is z=1.115000 Tap drift (diff=4.5450mm) — reset probe at 65.999,275.995 is z=3.907500 Tap drift (diff=2.7925mm) — reset probe at 65.999,275.995 is z=3.007500 Tap drift (diff=0.9000mm) — reset probe at 65.999,275.995 is z=1.110000 Tap drift (diff=1.8975mm) — reset probe at 65.999,275.995 is z=1.105000 Tap OK (diff=0.0050mm, stable 2/5) probe at 65.999,275.995 is z=0.925000 Tap drift (diff=0.1800mm) — reset Tap OK (diff=0.0000mm, stable 2/5) probe at 65.999,275.995 is z=0.927500 Tap OK (diff=0.0025mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=0.9275 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000)

probe: at 67.000,271.004 bed will contact at z=1.620000 probe: at 67.000,271.004 bed will contact at z=1.587500 probe: at 267.996,271.004 bed will contact at z=1.235000 probe: at 267.996,271.004 bed will contact at z=1.232500 probe: at 267.996,271.004 bed will contact at z=1.245000 probe: at 267.996,71.995 bed will contact at z=1.277500 probe: at 267.996,71.995 bed will contact at z=1.285000 probe: at 267.996,71.995 bed will contact at z=1.290000 probe: at 67.000,71.995 bed will contact at z=1.587500 probe: at 67.000,71.995 bed will contact at z=1.557500 probe: at 67.000,71.995 bed will contact at z=1.615000 Probe samples exceed tolerance. Retrying... probe: at 67.000,71.995 bed will contact at z=1.535000 probe: at 67.000,71.995 bed will contact at z=1.562500 probe: at 67.000,71.995 bed will contact at z=1.650000 probe: at 67.000,71.995 bed will contact at z=1.575000 probe: at 67.000,71.995 bed will contact at z=1.525000 probe: at 67.000,71.995 bed will contact at z=1.612500 probe: at 67.000,71.995 bed will contact at z=1.667500 probe: at 67.000,71.995 bed will contact at z=1.620000 probe: at 67.000,71.995 bed will contact at z=1.305000 probe: at 67.000,71.995 bed will contact at z=1.595000 probe: at 67.000,71.995 bed will contact at z=1.492500 probe: at 67.000,71.995 bed will contact at z=1.470000 probe: at 67.000,71.995 bed will contact at z=1.545000 probe: at 67.000,71.995 bed will contact at z=1.577500 probe: at 67.000,71.995 bed will contact at z=1.605000 probe: at 67.000,71.995 bed will contact at z=1.442500 probe: at 67.000,71.995 bed will contact at z=1.532500 probe: at 67.000,71.995 bed will contact at z=1.592500 probe: at 67.000,71.995 bed will contact at z=1.580000 probe: at 67.000,71.995 bed will contact at z=1.622500 probe: at 67.000,71.995 bed will contact at z=1.627500 probe: at 67.000,71.995 bed will contact at z=1.487500 probe: at 67.000,71.995 bed will contact at z=1.547500 probe: at 67.000,71.995 bed will contact at z=1.597500 probe: at 67.000,71.995 bed will contact at z=1.550000 probe: at 67.000,71.995 bed will contact at z=1.610000 probe: at 67.000,71.995 bed will contact at z=1.655000 probe: at 67.000,71.995 bed will contact at z=1.552500