[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C435;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22S148H;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=110V;bedw=550;ssr=SSR10DA;lot=20260618;uid=2ACAAE [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=610044000D51353234323830

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.7525 gap=1.2475 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.7525 gap=1.2475 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.7525 gap=1.2475 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-30.0091 gap=1.9909 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9847 gap=2.0153 fenetre=0.0244/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0244mm (tol=0.0500). Zero pose en butee=-30.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 375mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.995,340.003 is z=407.782500 probe at 49.995,340.003 is z=407.837500 Tap drift (diff=0.0550mm) — reset probe at 49.995,340.003 is z=407.827500 Tap OK (diff=0.0100mm, stable 2/5) probe at 49.995,340.003 is z=407.825000 Tap OK (diff=0.0025mm, stable 3/5) probe at 49.995,340.003 is z=407.870000 Tap drift (diff=0.0450mm) — reset probe at 49.995,340.003 is z=407.877500 Tap OK (diff=0.0075mm, stable 2/5) probe at 49.995,340.003 is z=407.865000 Tap drift (diff=0.0125mm) — reset Tap OK (diff=0.0000mm, stable 2/5) Tap OK (diff=0.0050mm, stable 3/5) probe at 49.995,340.003 is z=407.872500 Tap OK (diff=0.0025mm, stable 4/5) Tap OK (diff=0.0075mm, stable 5/5) VALIDATED: trigger_z=407.8650 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (50.0, 340.0) ~ point de tap (50.0, 340.0) Z calibration complete!

Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.998,340.003 is z=1.012500 probe at 49.998,340.003 is z=1.087500 Tap drift (diff=0.0750mm) — reset probe at 49.998,340.003 is z=1.107500 Tap drift (diff=0.0200mm) — reset probe at 49.998,340.003 is z=1.110000 Tap OK (diff=0.0025mm, stable 2/5) probe at 49.998,340.003 is z=1.115000 Tap OK (diff=0.0050mm, stable 3/5) Tap OK (diff=0.0050mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=1.1100 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (50.0, 340.0) ~ point de tap (50.0, 340.0) Z calibration complete! probe at 49.998,340.003 is z=486.112500 probe at 49.998,340.003 is z=486.115000 probe at 49.998,340.003 is z=486.117500 Tap OK (diff=0.0025mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) probe at 49.998,340.003 is z=486.120000 Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=486.1200 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) probe at 49.998,340.003 is z=486.102500 probe at 49.998,340.003 is z=486.085000 Tap drift (diff=0.0175mm) — reset probe at 49.998,340.003 is z=486.087500 VALIDATED: trigger_z=486.0850 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) probe at 49.998,340.003 is z=486.097500 Tap drift (diff=0.0150mm) — reset probe at 49.998,340.003 is z=486.100000 Tap drift (diff=0.0125mm) — reset probe at 49.998,340.003 is z=486.092500 Tap OK (diff=0.0075mm, stable 2/5) probe at 49.998,340.003 is z=486.107500 Tap OK (diff=0.0100mm, stable 2/5) probe at 49.998,340.003 is z=486.122500 Tap drift (diff=0.0250mm) — reset Tap drift (diff=0.0225mm) — reset

probe: at 54.997,315.001 bed will contact at z=2.085000 probe: at 54.997,315.001 bed will contact at z=2.070000 probe: at 54.997,315.001 bed will contact at z=2.075000 probe: at 380.001,315.001 bed will contact at z=2.182500 probe: at 380.001,315.001 bed will contact at z=2.202500 probe: at 380.001,315.001 bed will contact at z=2.187500 probe: at 380.001,83.000 bed will contact at z=2.090000 probe: at 380.001,83.000 bed will contact at z=2.097500 probe: at 54.997,83.000 bed will contact at z=2.080000 probe: at 54.997,83.000 bed will contact at z=2.092500 probe: at 54.997,83.000 bed will contact at z=2.085000 probe: at 217.505,202.498 bed will contact at z=2.142500 probe: at 217.505,202.498 bed will contact at z=2.197500 Probe samples exceed tolerance. Retrying... probe: at 217.505,202.498 bed will contact at z=2.190000 probe: at 217.505,202.498 bed will contact at z=2.210000 probe: at 217.505,202.498 bed will contact at z=2.255000 probe: at 217.505,202.498 bed will contact at z=2.240000 probe: at 217.505,202.498 bed will contact at z=2.222500 probe: at 217.505,202.498 bed will contact at z=2.235000 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=72.0, y=285.0, z=2.07500 front right screw : x=397.0, y=285.0, z=2.18750 : adjust CW 00:14 rear right screw : x=397.0, y=53.0, z=2.09750 : adjust CW 00:03 rear left screw : x=72.0, y=53.0, z=2.08500 : adjust CW 00:01 rear left screw : x=234.5, y=172.5, z=2.23500 : adjust CW 00:19