[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C335;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22DH;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=110V;bedw=500;ssr=SSR10DA;lot=20260618;uid=B3D7BD [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=630043000D51353234323830

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.6062 gap=1.3938 (chauffe, ignore) tap 2: pos=356.9847 gap=2.0153 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.8141 gap=2.1859 fenetre=0.1828/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=356.9481 spread=0.1828mm (tol=0.0500). Zero pose en butee=357.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.7769 gap=1.2231 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.7769 gap=1.2231 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 125mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=357.1797 gap=1.8203 fenetre=0.1828/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=357.0426 spread=0.1828mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-29.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.996,275.995 is z=346.575000 probe at 65.996,275.995 is z=285.682500 Tap drift (diff=60.8925mm) — reset probe at 65.996,275.995 is z=285.900000 Tap drift (diff=0.2175mm) — reset Tap OK (diff=0.0000mm, stable 2/5) probe at 65.996,275.995 is z=285.972500 Tap drift (diff=0.0725mm) — reset probe at 65.996,275.995 is z=285.902500 Tap drift (diff=0.0700mm) — reset Tap OK (diff=0.0000mm, stable 3/5) probe at 65.996,275.995 is z=288.765000 Tap drift (diff=2.8625mm) — reset probe at 65.996,275.995 is z=285.895000 Tap drift (diff=2.8700mm) — reset probe at 65.996,275.995 is z=285.905000 Tap drift (diff=0.0100mm) — reset Tap OK (diff=0.0000mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=285.9050 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (66.0, 276.0) ~ point de tap (66.0, 276.0)

Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.999,275.995 is z=395.605000 probe at 65.999,275.995 is z=398.050000 Tap rejete (vibration chassis, z=398.0500 > max-z_hop) -> pas de remontee, on poursuit la descente (1) probe at 65.999,275.995 is z=92.487500 probe at 65.999,275.995 is z=76.367500 Tap drift (diff=16.1200mm) — reset probe at 65.999,275.995 is z=6.042500 Tap drift (diff=70.3250mm) — reset probe at 65.999,275.995 is z=4.957500 Tap drift (diff=1.0850mm) — reset probe at 65.999,275.995 is z=4.955000 Tap OK (diff=0.0025mm, stable 2/5) Switch encore declenche (vibration) -> attente 2.0s puis nouvelle tentative (1/10) Switch encore declenche (vibration) -> attente 2.0s puis nouvelle tentative (2/10) probe at 65.999,275.995 is z=7.275000 Tap drift (diff=2.3200mm) — reset probe at 65.999,275.995 is z=9.887500 Tap drift (diff=2.6125mm) — reset probe at 65.999,275.995 is z=7.750000 Tap drift (diff=2.1375mm) — reset probe at 65.999,275.995 is z=4.947500 Tap drift (diff=2.8025mm) — reset probe at 65.999,275.995 is z=5.552500 Tap drift (diff=0.6050mm) — reset Tap drift (diff=0.5975mm) — reset Tap OK (diff=0.0000mm, stable 2/5) Tap OK (diff=0.0025mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=4.9550 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (66.0, 276.0) ~ point de tap (66.0, 276.0) Z calibration complete! probe at 65.999,275.995 is z=386.075000 probe at 65.999,275.995 is z=386.102500 Tap drift (diff=0.0275mm) — reset probe at 65.999,275.995 is z=386.105000 Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=386.1025 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000)

probe: at 67.000,271.004 bed will contact at z=1.710000 probe: at 67.000,271.004 bed will contact at z=1.880000 Probe samples exceed tolerance. Retrying... probe: at 67.000,271.004 bed will contact at z=1.875000 probe: at 67.000,271.004 bed will contact at z=1.860000 probe: at 67.000,271.004 bed will contact at z=1.890000 probe: at 267.996,271.004 bed will contact at z=1.787500 probe: at 267.996,271.004 bed will contact at z=1.815000 probe: at 267.996,271.004 bed will contact at z=1.817500 probe: at 267.996,71.995 bed will contact at z=1.735000 probe: at 267.996,71.995 bed will contact at z=1.767500 probe: at 267.996,71.995 bed will contact at z=1.770000 probe: at 67.000,71.995 bed will contact at z=1.785000 probe: at 67.000,71.995 bed will contact at z=1.835000 probe: at 67.000,71.995 bed will contact at z=1.815000 probe: at 67.000,71.995 bed will contact at z=1.832500 probe: at 67.000,71.995 bed will contact at z=1.822500 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=84.0, y=241.0, z=1.87500 front right screw : x=285.0, y=241.0, z=1.81500 : adjust CCW 00:07 rear right screw : x=285.0, y=42.0, z=1.76750 : adjust CCW 00:13 rear left screw : x=84.0, y=42.0, z=1.82250 : adjust CCW 00:06