[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C335;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22DH;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=500;ssr=SSR10DA;lot=20260618;uid=36C6E9 [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=680050000C51353234323830

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.3991 gap=1.6009 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.7891 gap=1.2109 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.3991 gap=1.6009 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.7769 gap=1.2231 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-29.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.996,275.995 is z=309.197500 probe at 65.996,275.995 is z=311.182500 Tap drift (diff=1.9850mm) — reset probe at 65.996,275.995 is z=311.127500 Tap drift (diff=0.0550mm) — reset Tap OK (diff=0.0000mm, stable 2/5) probe at 65.996,275.995 is z=311.130000 Tap OK (diff=0.0025mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=311.1300 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (66.0, 276.0) ~ point de tap (66.0, 276.0) Z calibration complete!

Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.999,275.995 is z=-1.385000 probe at 65.999,275.995 is z=-1.710000 Tap drift (diff=0.3250mm) — reset probe at 65.999,275.995 is z=0.275000 Tap drift (diff=1.9850mm) — reset probe at 65.999,275.995 is z=-2.025000 Tap drift (diff=2.3000mm) — reset probe at 65.999,275.995 is z=-0.182500 Tap drift (diff=1.8425mm) — reset probe at 65.999,275.995 is z=-2.347500 Tap drift (diff=2.1650mm) — reset probe at 65.999,275.995 is z=-0.512500 Tap drift (diff=1.8350mm) — reset probe at 65.999,275.995 is z=-2.672500 Tap drift (diff=2.1600mm) — reset probe at 65.999,275.995 is z=-0.670000 Tap drift (diff=2.0025mm) — reset probe at 65.999,275.995 is z=-2.995000 Tap drift (diff=2.3250mm) — reset probe at 65.999,275.995 is z=-3.320000 probe at 65.999,275.995 is z=-1.305000 Tap drift (diff=2.0150mm) — reset probe at 65.999,275.995 is z=1.655000 Tap drift (diff=2.9600mm) — reset Switch encore declenche (vibration) -> attente 2.0s puis nouvelle tentative (1/10) Switch encore declenche (vibration) -> attente 2.0s puis nouvelle tentative (2/10) probe at 65.999,275.995 is z=4.170000 Tap drift (diff=2.5150mm) — reset probe at 65.999,275.995 is z=-1.270000 Tap drift (diff=5.4400mm) — reset probe at 65.999,275.995 is z=-1.265000 Tap OK (diff=0.0050mm, stable 2/5) Tap OK (diff=0.0000mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=-1.2650 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (66.0, 276.0) ~ point de tap (66.0, 276.0) Z calibration complete!

probe: at 67.000,271.004 bed will contact at z=1.337500 probe: at 67.000,271.004 bed will contact at z=1.350000 probe: at 67.000,271.004 bed will contact at z=1.340000 probe: at 267.996,271.004 bed will contact at z=1.412500 probe: at 267.996,271.004 bed will contact at z=1.425000 probe: at 267.996,271.004 bed will contact at z=1.402500 probe: at 267.996,71.995 bed will contact at z=1.380000 probe: at 267.996,71.995 bed will contact at z=1.332500 probe: at 267.996,71.995 bed will contact at z=1.300000 Probe samples exceed tolerance. Retrying... probe: at 267.996,71.995 bed will contact at z=1.352500 probe: at 267.996,71.995 bed will contact at z=1.305000 probe: at 267.996,71.995 bed will contact at z=1.335000 probe: at 67.000,71.995 bed will contact at z=1.362500 probe: at 67.000,71.995 bed will contact at z=1.350000 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=84.0, y=241.0, z=1.34000 front right screw : x=285.0, y=241.0, z=1.41250 : adjust CW 00:09 rear right screw : x=285.0, y=42.0, z=1.33500 : adjust CCW 00:01 rear left screw : x=84.0, y=42.0, z=1.36250 : adjust CW 00:03